FITTING INSTRUCTIONS FOR
VU UTILITY CARGO TIE DOWN RAIL
Part Number 92144276
COPYRIGHT
Page 1 of 3
HOLDEN SERVICE PARTS OPERATIONS
Reproduction in whole or part
prohibited without written approval
Division of HOLDEN Ltd ACN 006 893 232
FD1001-1
FITTING INSTRUCTIONS
1. From each side of the vehicle, remove the front, centre and rear side rail cap screws attaching the
side rail capping.
REMOVE & DISCARD
CAP SCREW, 3 PLACES
R & L SIDE
FD1001
21MR01
COPYRIGHT
Page 2 of 3
FD1001-2
HOLDEN SERVICE PARTS OPERATIONS
Reproduction in whole or part
prohibited without written approval
Division of HOLDEN Ltd ACN 006 893 232
For Vehicles Not Fitted with a Sports Bar.
2. Install 11.5 mm compression spacers at 3
places. Refer Figure 2, 3 & 4
3. Align the tie-down rail with the centre hole
and install the screw and washer. Do Not
Tighten. Refer Figure 2.
4. Attached front mounting plate of tie-down rail
by installing screw and flat washer. Do Not
Tighten. Refer Figure 3.
4. Attach rear mounting plate of rail by installing
screw and flat washer. Refer Figure 4.
5. Tighten all screws to specified torque. Refer
Figure 2, 3 & 4.
6. Repeat installation for the opposite side.
7. Place fitting instruction in the vehicles glove
box. FIGURE 4
FIGURE 2
FIGURE 3
1
1
1
1
SCREW
WASHER
1
SCREW
WASHER
118.0 ~ 22.0Nm
18.0 ~ 22.0Nm
18.0 ~ 22.0Nm
1
SCREW
WASHER
SPACER
11.5 mm
SPACER
11.5 mm
SPACER
11.5 mm
FD1001
21MR01
COPYRIGHT
Page 3 of 3
FD1001-3
HOLDEN SERVICE PARTS OPERATIONS
Reproduction in whole or part
prohibited without written approval
Division of HOLDEN Ltd ACN 006 893 232
For Vehicles Fitted with a Sports Bar.
8. Install 16.0mm compression spacers at the
centre and the front mounting points. Refer
Figures 5 & 6.
9. Install 11.5mm compression spacer at the
rear tie-down rail mounting plate. Refer
Figure 7.
10 Align the tie-down rail with the centre screw
hole and install the spacer plate, screw and
flat washer. Do Not Tighten. Refer Figure 5.
11. Attached front mounting plate of the tie-down
rail by installing screw and flat washer. Do
Not Tighten. Refer Figure 6.
12. Attach rear mounting plate of tie-down rail by
installing flat washer and screw.
13. Tighten all screws to specified torque. Refer
Figure 5, 6 & 7.
14. Place fitting instructions in the vehicles glove
box.
FIGURE 7
FIGURE 5
FIGURE 6
1
1
SCREW
WASHER
SPACER
11.5 mm
PART No. DESCRIPTION QTY
CARGO TIE-DOWN RAIL 2
SCREW 6
WASHER 6
COMPRESSION TUBE 11.5mm LONG 6
COMPRESSION TUBE 16.0mm LONG 4
SPACER PLATE 2
FD1001 FITTING INSTRUCTION BOOKLET 1
PARTS LIST
SPORTS
BAR
SCREW
WASHER
SPACER
16 mm
1
1
1
1
SCREW
WASHER
SPACER
16 mm LONG
SPACER
PLATE
SPORTS
BAR
FD1001
21MR01
18.0 ~ 22.0Nm
18.0 ~ 22.0Nm
18.0 ~ 22.0Nm