FITTING INSTRUCTIONS FOR

VU SERIES UTILITY SOFT TONNEAU COVER

Page 1 of 5

FD1006-1

HOLDEN SERVICE PARTS OPERATIONS

Reproduction in whole or part

prohibited without written approval

Division of HOLDEN Ltd ACN 006 893 232

Part Number: 92100308 Original Equipment Package

Part Number: 92143494 Sportsman Package

FD1006

26FE01

Page 2 of 5

FD1006-2

HOLDEN SERVICE PARTS OPERATIONS

Reproduction in whole or part

prohibited without written approval

Division of HOLDEN Ltd ACN 006 893 232

1. Install the support bow mounting brackets, 2

places each side, into the locating holes in

the side rail cap channel at the positions

shown. Insert the upper edge of the bracket

into the channel and rotate downwards.

Refer Figure 1.

NOTE: This is only required on models not

already fitted with a tonneau cover.

2. Insert the support bows into the brackets.

Refer Figure 2.

NOTE: The front bow is longer than the rear.

3. At the front of the rolled up tonneau up,

topside out, insert the locking strip into the

middle slot of the front bow assembly. Slide

the tonneau fully across the front bow

assembly. Refer Figure 3.

NOTE: Additional slots in the front bow may

be used for tensioning the tonneau.

4. Install the front bow assembly and tonneau

onto the vehicle by inserting each end of the

bow into the slot, tilting up and pulling into

place at the front of the side rail caps as

shown. Refer Figure 4.

FIGURE 4

FIGURE 3

LOCKING

STRIP

FRONT BOW

ASM.-MIDDLE

SLOT

FRONT BOW

ASSEMBLY

FITTING INSTRUCTIONS

SUPPORT BOW

MOUNTING BRACKET

4 PLACES

FIGURE 1

FIGURE 2

SUPPORT BOW

TONNEAU

ROLLED UP

FD1006

26FE01

FD992

06NO00

Page 3 of 5

FD1006-3

HOLDEN SERVICE PARTS OPERATIONS

Reproduction in whole or part

prohibited without written approval

Division of HOLDEN Ltd ACN 006 893 232

5. Fold the front of the tonneau onto the load

compartment front upper panel and attach.

The tonneau has a magnetic strip that will

attach to the panel surface. Refer Figure 5.

6. Unroll the tonneau over the bows. By using

the finger loops, pull the tonneau's plastic

strip over and into the slot in the side rail

capping, beginning at the centre of the

endgate, then working across the rear and

then along each side. Refer Figure 6.

7. By hand, locate the strip by pushing it down

to smooth it along the slot in the rail capping.

Check tautness of the tonneau and adjust by

relocating the front locking strips in the front

bow assembly. Refer Figure 7.

8. For large or protruding loads, use the hooks

attached to the elastic cord in the tonneau.

Locate these into the side rail capping slot to

allow the tonneau fit around or over larger

size loads. Refer Figure 8.

FIGURE 6

FIGURE 5

FIGURE 7

FIGURE 8

TONNEAU

MAGNETIC

STRIP

A-A

FITTING INSTRUCTIONS...continued

RAIL

CAPPING

SLOT

RAIL

CAPPING

SLOT

RAIL

CAPPING

SLOT

HOOK

TONNEAU

PUSH DOWN

TONNEAU

PLASTIC STRIP

PULL

FD1006

26FE01

Page 4 of 5

FD1006-4

HOLDEN SERVICE PARTS OPERATIONS

Reproduction in whole or part

prohibited without written approval

Division of HOLDEN Ltd ACN 006 893 232

1. Using the finger loops and starting at the

endgate, pull out and up, the plastic retaining

strip from the slot in the endgate and side

rail capping. Refer Figure 10 Detach the front

magnetic flap by lifting. When fitted with the

sports bar, lift the velcro fixed overlapped

joints to separate. Refer Figure 10.

2. Remove the front bow assembly by pushing

it forward and tilting down each side.

Remove tonneau and all bows from vehicle.

Refer Figure 11.

The support bow mounting brackets may be

left installed for later reuse.

3. Lay the tonneau flat, top side up. Fold the

bottom corner up, to form a triangle. Refer

Figure 12.

FIGURE 10

FIGURE 9

FIGURE 11

FIGURE 12

REMOVAL INSTRUCTIONS

FRONT BOW

ASSEMBLY

TONNEAU

9. For vehicles fitted with the sports bar, the

tonneau fits around the bar mounting points.

The overlap fitment of the tonneau mounting

location is fixed into position with velcro at

the front and rear bar mounting points.

10. Place the storage bag in the rear trim pocket

between the seats.

11. Place the warranty card and fitting

instructions in the glove box.

PULL OUT

FINGER

LOOPS

FITTING INSTRUCTIONS...continued

OVERLAP

JOINT

OVERLAP

JOINT

FD1006

26FE01

Page 5 of 5

FD1006-5

HOLDEN SERVICE PARTS OPERATIONS

Reproduction in whole or part

prohibited without written approval

Division of HOLDEN Ltd ACN 006 893 232

5. Roll up the tonneau, starting from the point of

the triangle. Refer Figure 14.

6. Store the tonneau, support brackets and

bows in the bag provided and stow behind

seats inside vehicle. Refer Figure 15.

7. Place fitting instructions in the glove box of

the vehicle.

PART No. DESCRIPTION QTY

92100308 SOFT TONNEAU COVER (ORIGINAL EQUIPMENT PACKAGE) 1

92143494 SOFT TONNEAU COVER (SPORTSMAN PACKAGE) 1

TONNEAU SUPPORT BOW - FRONT 1

TONNEAU SUPPORT BOW - REAR 1

TONNEAU SUPPORT BOW MOUNTING BRACKET 4

STORAGE BAG 1

SOFT TONNEAU COVER FITTING INSTRUCTIONS 1

FRONT TONNEAU BOW ASSEMBLY

FD1006

FIGURE 14

FIGURE 15

PARTS LIST

REMOVAL INSTRUCTIONS... continued

STORAGE BAG

SUPPOORT

BRACKETS

TONNEAU SUPPORT

BOWS

FIGURE 13

4. Fold the other bottom corner up to form a

smaller triangle. Refer Figure 13.

FD1006

26FE01