FITTING INSTRUCTIONS FOR
CARGO ORGANISER FOR
SEDAN, COUPE AND WAGON
FD1219
03AUG04
COPYRIGHT
Reproduction in whole or part
prohibited without written approval
HOLDEN LTD
Division of HOLDEN Ltd ACN 006 893 232
Page 1 of 4
TOOLS REQUIRED:
Trim Removal Tool, Drill, 7.5mm Drill Bit.
Part No. 92177440
FITTING INSTRUCTIONS FOR
CARGO ORGANISER FOR
SEDAN, COUPE AND WAGON
FD1219
03AUG04
COPYRIGHT
Reproduction in whole or part
prohibited without written approval
HOLDEN LTD
Division of HOLDEN Ltd ACN 006 893 232
FIGURE 1
FITTING INSTRUCTIONS:
MOUNTING CARGO ORGANISER IN VEHICLE
Sedan and Coupe Only
1. On sedan, using a trim removal tool, remove the retainer
(1) on both sides of the rear compartment wall. Refer to
Figure 1.
2. On coupe, lift out the spare wheel cover. On both sides,
fold up the rear quarter panel carpet trim to locate the
position of the trim holes. Use a 7.5 mm drill bit to drill out
the corresponding hole positions in the carpet.
Refer to Figure 2 for the following:
3. In the sheetmetal, drill out the holes (1) (2 places) using
a drill with a 7.5 mm drill bit.
4. Remove the swarf.
5. Apply primer or suitable corrosion protector to the
sheetmetal hole (2 places).
6. Install the luggage retainer (1) on both sides of the rear
compartment wall. Refer to Figure 3.
1
FIGURE 3
1
FIGURE 2
1
Page 2 of 4
FITTING INSTRUCTIONS FOR
CARGO ORGANISER FOR
SEDAN, COUPE AND WAGON
FD1219
03AUG04
COPYRIGHT
Reproduction in whole or part
prohibited without written approval
HOLDEN LTD
Division of HOLDEN Ltd ACN 006 893 232
FITTING INSTRUCTIONS: - continued...
INSTALLING AND USING CARGO ORGANISER
Sedan and Coupe Only
Refer to Figure 4 for the following:
7. Place the cargo organiser into the rear of the vehicle.
NOTE: It is recommended that the low edge of the cargo
organiser faces towards the rear of the vehicle.
8. Attach the loops (1) (2 places) to the luggage retainers
(2) installed in step 6.
Wagon Only
Refer to Figure 5 for the following:
9. Place the cargo organiser into the rear of the vehicle.
10. Attach at least two luggage tie downs (1) in suitable
positions for fitment of the cargo organiser.
11. Attach at least two cargo organiser loops (2) to the
luggage tie downs. Stretch loops over the luggage tie
downs for positive retention of the cargo organiser.
Sedan, Wagon and Coupe
12. Unclip the snap fastener (1) (2 places) on the outside of
the cargo organiser. Refer to Figure 6.
FIGURE 6
FIGURE 4
1
1
Page 3 of 4
FIGURE 5
21
2
FITTING INSTRUCTIONS FOR
CARGO ORGANISER FOR
SEDAN, COUPE AND WAGON
FD1219
03AUG04
COPYRIGHT
Reproduction in whole or part
prohibited without written approval
HOLDEN LTD
Division of HOLDEN Ltd ACN 006 893 232
FIGURE 9
FITTING INSTRUCTIONS: - continued...
13. Unfold the cargo organiser. Refer to Figure 7.
14. Fasten the two end snap fasteners (1) Refer to
Figure 8.
15. Raise the partitions (1) as required. Secure the raised
partitions using the snap fastener (2) (4 places on each
partition). Refer to Figure 9.
NOTE: If the full volume of the rear compartment needs
to be utilised, then the cargo organiser may be collapsed
and left in position.
CARGO ORGANISER
PARTS LIST
PART NUMBER DESCRIPTION QUANTITY
92177440 CARGO ORGANISER 1
92087976 RETAINER - LUGGAGE (NOT REQUIRED FOR WAGON) 2
FD1219 FITTING INSTRUCTIONS 1
FD796 PROOF OF WARRANTY CARD 1
FIGURE 8
1
Page 4 of 4
1
1
A
2
1
VIEW A
FIGURE 7