FITTING INSTRUCTIONS FOR

VU SERIES UTILITY SOFT TONNEAU COVER

Page 1 of 5

FD992-1

HOLDEN SERVICE PARTS OPERATIONS

Reproduction in whole or part

prohibited without written approval

Division of HOLDEN Ltd ACN 006 893 232

Part Number: 92144212 Tradesman

FD992

22JA01

Page 2 of 5

FD992-2

HOLDEN SERVICE PARTS OPERATIONS

Reproduction in whole or part

prohibited without written approval

Division of HOLDEN Ltd ACN 006 893 232

1. Install the support bow mounting brackets, 2

places each side, into the locating holes in

the side rail cap channel at the positions

shown. Insert the upper edge of the bracket

into the channel and rotate downwards.

Refer Figure 1.

NOTE: This is only required on models not

already fitted with a tonneau cover.

2. Insert the support bows into the brackets.

Refer Figure 2.

NOTE: The front bow is longer than the rear.

3. With the tonneau rolled up, topside out,

insert the locking strip at the front of the

tonneau into the front bow assembly slot.

Slide the tonneau fully across the front bow

assembly. Refer Figure 3.

NOTE: Additional slots in the front bow may

be used for tensioning the tonneau and used

in conjunction with the cord for adjustment.

4. Install the front bow assembly and tonneau

onto the vehicle by inserting each end of the

bow into the slot, tilting up and pulling into

place at the front of the side rail caps as

shown. Refer Figure 4.

FIGURE 4

FIGURE 3

LOCKING

STRIP

FRONT BOW

ASSEMBLY

FRONT BOW

ASSEMBLY

FITTING INSTRUCTIONS

SUPPORT BOW

MOUNTING BRACKET

4 PLACES

FIGURE 1

FIGURE 2

SUPPORT BOW

TONNEAU

ROLLED UP

FD992

05JA01

FD992

06NO00

Page 3 of 5

FD992-3

HOLDEN SERVICE PARTS OPERATIONS

Reproduction in whole or part

prohibited without written approval

Division of HOLDEN Ltd ACN 006 893 232

5. Fold the front of the tonneau onto the load

compartment front upper panel. The tonneau

has a magnetic strip that will attach to the

panel surface. Refer Figure 5.

6. Unroll the tonneau over the bows and insert

the clips into the endgate and side rail

capping, beginning at the centre of the

endgate, working across the rear and then

along each side. Refer Figure 6.

7 For large loads or to re-tension the tonneau

cover, the cord can be lengthened or

shortened. Untie the knot either side near the

front and adjust the cord length as required.

Retie using a double hitch knot. Refer Figure

8. Place the warranty card and fitting

instructions in the glove box.

9. Place the storage bag in the rear trim pocket

between the seats. Refer Figure 8..

FIGURE 6

FIGURE 5

FIGURE 7

FIGURE 8

TONNEAU

MAGNETIC

STRIP

A-A

RAIL

CAPPING CLIP

TONNEAU

KNOT

FITTING INSTRUCTIONS

STOWAGE

NET

STORAGE BAG

FD992

22JA01

Page 4 of 5

FD992-4

HOLDEN SERVICE PARTS OPERATIONS

Reproduction in whole or part

prohibited without written approval

Division of HOLDEN Ltd ACN 006 893 232

1. Remove clips from the engate and side rail

capping and detach magnetic front flap by

lifting. Refer Figure 1.

2. Remove the front bow assembly by pushing

it forward and tilting down each side.

Remove tonneau and all bows from vehicle.

Refer Figure 2.

3. Lay the tonneau flat, top side up. Fold the

bottom corner up, to form a triangle. Refer

Figure 3.

4. Fold the other bottom corner up to form a

smaller triangle. Refer Figure 4.

FIGURE 1

FIGURE 2

FIGURE 3

REMOVAL INSTRUCTIONS

RAIL

CAPPING CLIP

TONNEAU

FRONT BOW

ASSEMBLY

TONNEAU

FIGURE 4

FD992

22JA01

Page 5 of 5

FD992-5

HOLDEN SERVICE PARTS OPERATIONS

Reproduction in whole or part

prohibited without written approval

Division of HOLDEN Ltd ACN 006 893 232

5. Roll up the tonneau, starting from the point of

the triangle. Refer Figure 5.

6. Store the tonneau, support brackets and

bows in the bag provided. Stow behind seats

inside vehicle. Refer Figure 6.

PART No. DESCRIPTION QTY

SOFT TONNEAU COVER 1

TONNEAU SUPPORT BOW - FRONT 1

TONNEAU SUPPORT BOW - REAR 1

TONNEAU SUPPORT BOW MOUNTING BRACKET 4

STORAGE BAG 1

FD796 WARRANTY CARD 1

FD992 SOFT TONNEAU COVER FITTING INSTRUCTIONS 1

FRONT TONNEAU BOW ASSEMBLY

FIGURE 5

FIGURE 6

PARTS LIST

REMOVAL INSTRUCTIONS

STORAGE BAG

SUPPOORT

BRACKETS

TONNEAU SUPPORT

BOWS

FD992

22JA01