FITTING INSTRUCTIONS FOR
VT REAR SPOILER
IMPORTANT: Please read the following instructions
carefully before fitting is attempted.
1. Clean rear deck lid. Ensure all protective wax,
grime and dust is completely removed.
NOTE: Avoid paint damage. Spoiler may be rested on a cloth
to prevent scratching.
2. Remove drilling template from the hardware kit, and check drilling positions.
3. Position template carefully on deck lid RHS first, then LHS. Carefully mark the outer drilling position. Two
holes on the LHS. Three holes on the RHS, the larger hole to be drilled through the outer panel only.
4. Apply masking tape around areas to be drilled
NOTE: The template is handed. RHS on the top, invert template to show LHS.
5. DOUBLE CHECK ALL POINTS BEFORE PROCEEDING.
Use a centre punch to mark hole positions for drilling.
NOTE: Place wooden chocks under area to be drilled.
6. Use a 3mm drill bit to pre-drill holes through the deck lid. Ensure to penetrate the outer panel only when pre-
drilling the third hole on the RHS(wiring hole).
7. Re-drill the four mounting positions with a 10mm drill bit. Use a 15mm hole saw to re-drill the hole for the
wiring.
8. Deburr all holes - rustproof using Zinc Chromate or equivalent. Remove masking tape.
NOTE: If primed only spoiler has been ordered, paint spoiler then fit brake lamp and harness, prior to installation
to deck lid, refer fig. 1, view A.
9. Carefully place rear spoiler on deck lid and pass wire through 15mm drilled hole.
10. From underside of deck lid, install rubber washers to protruding studs. Temporarily fix spoiler into
position with nuts supplied. ENSURE SPOILER IS IN CORRECT POSITION.
Install rubber washers to bolts then use bolts to complete assembly to decklid. Tighten all fasteners
( 2-5 Nm ).
11. Attach wiring connector from spoiler to the available connector within the deck lid.
NOTE: When fitting spoiler to Calais, use patch harness (M41694), refer fig. 2, views A and B.
NOTE: By law, an interior high mounted rear brake lamp must be disconnected when fitting a vehicle with a
rear spoiler.
12. Disconnect high mounted brake lamp. Remove bulb (discard) and reconnect.
FD843
17AU98
COPYRIGHT
Page 1 of 4
3327c-01
HOLDEN SERVICE PARTS OPERATIONS
Reproduction in whole or part
prohibited without written approval
Division of HOLDEN Ltd ACN 006 893 232
A-A
SECTION
INSTALLED CONDITION
REAR COMPARTMENT
LID OUTER PANEL
REAR COMPARTMENT
LID INNER PANEL
B-B
SECTION
INSTALLED CONDITION
ALL MODELS EXCEPT CALAIS
REAR COMPARTMENT
LID OUTER PANEL
REAR COMPARTMENT
LID INNER PANEL
EXISTING FREE
CONNECTOR
WITHIN DECKLID
B
DRILL 15,0 DIA. HOLE
FOR WIRING HARNESS,
DEBUR AND COAT WITH
ZINC CHROMATE
OR EQUIVALENT
DRILLING
TEMPLATE
DRILL 10,0 DIA HOLES (4 PLACES)
DEBUR AND COAT WITH ZINC
CHROMATE OR EQUIVALENT
A
A
REAR SPOILER
REMOVE GLOBE FROM EXISTING
HIGH MOUNT BRAKE LAMP
(REAR PARCEL SHELF)
NUT
2.0 - 5.0Nm
(2 PLACES)
BOLT
2.0 - 5.0Nm
(2 PLACES)
RUBBER WASHER
(4 PLACES)
FD843
17AU98 Figure 1
COPYRIGHT
Page 2 of 4
3327c-02
HOLDEN SERVICE PARTS OPERATIONS
Reproduction in whole or part
prohibited without written approval
Division of HOLDEN Ltd ACN 006 893 232
B
SCREW
(4 PLACES)
BRAKE LAMP
AND HARNESS
ASSEMBLY
FEED WIRING THROUGH
CHANEL IN SPOILER
A
VIEW A
FOR PRIMED ONLY SPOILER
STUD
(2 PLACES)
PARTS LIST
PART NUMBER DESCRIPTION QUANTITY
Rear spoiler assembly: 1
92078990 “S” Pack, primed only*
92135775 “S” Pack, Bermuda Blue
92135776 “S” Pack, Heron White
92135777 “S” Pack, Raven
92133788 “SS”, Bermuda Blue
92133789 “SS”, Heron White
92133790 “SS”, Raven
92142078 Small parts kit, consists of: 1
11063471 Nut 2
11088121 Bolt 2
92043323 Rubber washer 4
INCLUDED WITH PRIMED ONLY REAR SPOILER PACKAGE (AS
SEPARATE PARTS):
92080447 Brake lamp/harness assembly 1
Screw 4
Threaded stud 2
*NOTE: For “S” Pack, primed only, rear spoiler, brake lamp and harness
assembly is supplied but not fitted. Paint spoiler then fit brake lamp and
harness assembly using four screws provided.
NOT INCLUDED IN REAR SPOILER PACKAGE,
BUT MANDATORY TO FIT (CALAIS ONLY):
M41694 Patch harness 1
NOT INCLUDED IN REAR SPOILER PACKAGE,
BUT RECOMMENDED TO FIT:
Strut, Decklid 2
CALAIS PATCH
HARNESS
CALAIS PATCH
HARNESS
SEPARATE EXISTING
MULTI-PIN TAIL LAMP
CONNECTORS AND
INSERT PATCH
HARNESS
TAPE PATCH HARNESS
TO EXISTING HARNESS
WITH ELECTRICAL TAPE
VIEW A
VIEW B
B
A
C-C
SECTION
INSTALLED CONDITION
CALAIS ONLY
REAR COMPARTMENT
LID OUTER PANEL
PATCH
HARNESS
C
C
FD843
05NO98 Figure 2
COPYRIGHT
Page 3 of 4
3327d-03
HOLDEN SERVICE PARTS OPERATIONS
Reproduction in whole or part
prohibited without written approval
Division of HOLDEN Ltd ACN 006 893 232
REAR
COMPARTMENT
LID INNER PANEL
VT REAR SPOILER DRILLING TEMPLATE
DECK LID
OUTER
EDGE
DRILL 10.0 DIA. HOLES
THRU BOTH PANELS
(2 PLACES)
DRILL 15.0 DIA. HOLE
THRU OUTER PANEL ONLY
(RH SIDE ONLY)
DECKLID REAR EDGE
FD843
17AU98
Page 4 of 4
3327c-04
HOLDEN SERVICE PARTS OPERATIONS
COPYRIGHT
Reproduction in whole or part
prohibited without written approval
Division of HOLDEN Ltd ACN 006 893 232
IMPORTANT: BEFORE USING TEMPLATE
CHECK DIMENSIONS HAVE
NOT ALTERED AFTER
PHOTOCOPYING
72.0
155.5