COPYRIGHT
HOLDEN SERVICE PARTS OPERATIONS
Reproduction in whole or part
prohibited without written approval
Division of HOLDEN Ltd ACN 006 893 232
G662
FITTING INSTRUCTIONS FOR
VY S & SS SEDAN REAR SPOILER
Part Nos 92144105 (S), 92144106 (SS)
Page 1 of 6
FD1073
05AU02
COPYRIGHT
HOLDEN SERVICE PARTS OPERATIONS
Reproduction in whole or part
prohibited without written approval
Division of HOLDEN Ltd ACN 006 893 232
FITTING INSTRUCTIONS FOR
VY S & SS SEDAN REAR SPOILER
TOOLS REQUIRED:
Power Drill, 3 mm Drill Bit, 9 mm Drill Bit, 18 mm Drill
Bit, 10 mm Socket, Torque Wrench, Phillips Head
Screwdriver, Allen Key, Trim Clip Removal Tool, File &
Corrosion Protection Paint Primer.
FITTING INSTRUCTIONS:
PREPARATION
NOTE: The rear spoiler is supplied ready to be painted.
Prior to painting, refer to the paint manufactures
recommendations for surface preparation.
1. SS SEDAN ONLY: The SS rear spoiler requires
painting vehicle colour on the upper surface and
underside edges, and skirt black on the underside.
The colour separation point, for masking, is
indicated by a groove on the underside of the
spoiler. Refer Figure 2.
The rear spoiler on the S sedan is painted uniform
vehicle colour.
2. After the paint has sufficiently cured (refer to paint
manufacturers recommendations), fit the high
mount stop lamp as follows:
Manipulate the wiring harness through the cavity.
If required, make a hook from a length of wire to
aid pulling the connector through.
Install the screws and tighten to the specified
torque.
Fit the caps.
Refer Figure 1.
FIGURE 2
G662
Page 2 of 6
HIGH MOUNT
STOP LAMP
SCREW CAPS
1
1
5.0 Nm
SCREWS
FIGURE 1
A-A
A
A
GROOVE
VEHICLE
COLOUR
SKIRT
BLACK
REAR
SPOILER
FD1073
05AU02
FIGURE 3
11.0 - 3.0 Nm A
1
SCREW
A
SPARE WHEEL
STOWAGE COVER
HOOK
RETAINER
(14 PLACES)
REAR COMPARTMENT
LID CARPET
COPY & CUT
OUT TEMPLATES
CHECK SCALE
COPYRIGHT
HOLDEN SERVICE PARTS OPERATIONS
Reproduction in whole or part
prohibited without written approval
Division of HOLDEN Ltd ACN 006 893 232
FITTING INSTRUCTIONS FOR
VY S & SS SEDAN REAR SPOILER
G662
FITTING INSTRUCTIONS: - continued...
3. If fitted, remove the rear compartment lid carpet as
follows:
Remove the screw attaching the spare wheel
stowage cover hook.
Using a suitable trim clip removal tool, remove
the retainers attaching the rear compartment lid
carpet (14 places).
Remove the carpet from the rear compartment
lid. Refer Figure 3.
4. Copy and cut out the drilling templates on Page 6.
NOTE: Ensure the template is the correct size by
measuring the copied scale. Refer Figure 4.
FIGURE 4
Page 3 of 6
005050
9 mm HOLE9 mm HOLE
4040
3030
2020
1010
00
FD1073
05AU02
COPYRIGHT
HOLDEN SERVICE PARTS OPERATIONS
Reproduction in whole or part
prohibited without written approval
Division of HOLDEN Ltd ACN 006 893 232
FITTING INSTRUCTIONS FOR
VY S & SS SEDAN REAR SPOILER
FITTING INSTRUCTIONS: - continued...
5. Place a mark on the right-hand outer edge of the rear compartment lid, measuring 470 mm from the front
corner in a straight line. Refer Figure 5.
NOTE: Protect the paintwork in the area where the holes are to be drilled with masking tape.
6. Place the right-hand side template on the rear compartment lid (right hand side), aligning the corner with the
arrow to the mark made in Step 5 and the edge of the template with the side edge of the rear compartment lid.
Refer Figure 4.
7. Mark the centre of the two mounting holes and the wiring harness hole (right hand side only).
8. Using the left-hand side template repeat Steps 4 to 6 on the left hand side of the rear compartment lid.
G662
Page 4 of 6
FIGURE 5
470 mm
TEMPLATE
WIRING HARNESS HOLE
(RIGHT HAND SIDE ONLY)
MOUNTING
HOLES
MARK
ARROW
FIGURE 6
9. Sit the spoiler in position on the rear compartment
lid and check that the mounting studs and holes
align with the mounting hole marks. Adjust as
required.
10. Open the rear compartment lid slightly and place a
block of wood under the drilling locations. Refer
Figure 6.
11. Carefully drill the mounting holes. Initially drill 3mm
pilot holes, followed by 9 mm holes. Drill through
the inner and outer rear compartment lid panels.
12. Carefully drill the wiring harness hole on the right-
hand side only THROUGH THE OUTER SKIN
ONLY. Initially drill a 3.0 mm pilot hole, followed by
an 18.0 mm hole (right-hand side only).
OPEN REAR
COMPARTMENT LID
WOOD
BLOCKS
REAR COMPARTMENT
LID SIDE EDGE
FD1073
05AU02
PART NUMBER DESCRIPTION QUANTITY
92144105 ‘S’ SPOILER KIT
92084173 RAW SPOILER 1
92084175 HIGH MOUNTED STOP LAMP 1
92144553 SPOILER SPK 1
92144106 ‘SS’ SPOILER
92084177 RAW SPOILER 1
92084179 HIGH MOUNTED STOP LAMP 1
92144553 SPOILER SPK 1
92144553 SPOILER SPK
VY S LH GASKET 1
VY S RH GASKET 1
VY SS LH GASKET 1
VY SS RH GASKET 1
M5 x 8 mm HEX FLANGE SCREW 2
M6 STUD x 35 mm 4
M6 FLANGE NUT 4
92043323 SEAL, MOUNTING 4
FD1073 FITTING INSTRUCTIONS 1
VY S & SS SEDAN REAR SPOILER KITS
PARTS LIST
1
1
2.0 - 5.0 Nm
REAR SPOILER
NUT
SEAL
STUD
COPYRIGHT
HOLDEN SERVICE PARTS OPERATIONS
Reproduction in whole or part
prohibited without written approval
Division of HOLDEN Ltd ACN 006 893 232
REAR SPOILER
CONNECTOR
BODY HARNESS
CONNECTOR
FITTING INSTRUCTIONS FOR
VY S & SS SEDAN REAR SPOILER
FIGURE 7
FIGURE 8
FITTING INSTRUCTIONS: - continued...
13. Debur the drill holes and remove all swarf. Apply
primer to the bare metal as required.
14. Install the four studs into the rear spoiler. Refer
Figure 7.
15. Feed the high mount stop lamp connector through
the wiring harness hole (right-hand side) and install
the rear spoiler onto the rear compartment lid.
Secure with seals and nuts (hand tighten only)
Refer Figure 7.
16. Check the alignment of the spoiler on the rear
compartment lid and tighten the nuts to the
specified torque. .
17. From within the rear compartment cavity, unclip the
body wiring harness connector from the rear
compartment lid. Connect the rear spoiler harness
connector to the body harness connector and clip
back in original position. Refer Figure 8.
Refer Figure 7
18. Check the high mount stop lamp operation.
19. Refit the rear compartment lid carpet if fitted.
20. Place a copy of the instructions in the glovebox.
G662
Page 5 of 6
FD1073
05AU02
COPYRIGHT
HOLDEN SERVICE PARTS OPERATIONS
Reproduction in whole or part
prohibited without written approval
Division of HOLDEN Ltd ACN 006 893 232
FITTING INSTRUCTIONS FOR
VY S & SS SEDAN REAR SPOILER
G662
Page 6 of 6
0 50
0 50
RIGHT-HAND SIDE DRILLING TEMPLATE
LEFT-HAND SIDE DRILLING TEMPLATE
9 mm HOLE
9 mm HOLE
9 mm HOLE
9 mm HOLE
18 mm HOLE
(RIGHT-HAND SIDE ONLY)
FD1073
05AU02