FITTING INSTRUCTIONS FOR
VY - VZ WAGON ROOF BARS
FD1317
15NOV04
Reproduction in whole or part
prohibited without written approval
HOLDEN LTD
Division of HOLDEN Ltd ACN 006 893 232
COPYRIGHT
Part No. 92171977
Page 1 of 5
TOOLS REQUIRED:
10mm Socket or Spanner, Security Bit (supplied), Knife.
FITTING INSTRUCTIONS FOR
VY - VZ WAGON ROOF BARS
FD1317
15NOV04
Reproduction in whole or part
prohibited without written approval
HOLDEN LTD
Division of HOLDEN Ltd ACN 006 893 232
COPYRIGHT
Page 2 of 5
FITTING INSTRUCTIONS:
Refer to Figure 2 for the following:
1. Peel away a part of strip (1) from each end of the roof bar
(2) to provide access to the hole (3) in the roof bar (4
places). Refer to Figure 1.
2. Slide the roof bar support (1) to the end of the slot in the
roof bar (2) (4 places).
3. Finger tighten the screw (1) to attach the roof bar
support (2) to the roof bar (3) (4 places). If required, use
a 10 mm spanner. Refer to Figure 3.
FIGURE 2
1
2
2
3
1
FIGURE 3
FIGURE 1
2
1
3
FITTING INSTRUCTIONS FOR
VY - VZ WAGON ROOF BARS
FD1317
15NOV04
Reproduction in whole or part
prohibited without written approval
HOLDEN LTD
Division of HOLDEN Ltd ACN 006 893 232
COPYRIGHT
FITTING INSTRUCTIONS: - continued...
NOTE: In the following steps, ensure that the retainers
are not moved out of position.
4. Insert the rectangular retainer (1) into the roof channel (4
places). Refer to Figure 4.
5. Move the retainers to the recommended positions.
Refer to Figure 5.
6. Position the support piece (1) on the roof channel so that
the retainer (2) is located in the gap (3) within in the
support piece (4 places). Ensure that the support pieces
identified "FRONT" are at the front of the vehicle and
that the support pieces identified "REAR" are at the rear
of the vehicle. Refer to Figure 6.
FIGURE 6
Page 3 of 5
1
23
FIGURE 4
1
FIGURE 5
400.0 700.0
FITTING INSTRUCTIONS FOR
VY - VZ WAGON ROOF BARS
FD1317
15NOV04
Reproduction in whole or part
prohibited without written approval
HOLDEN LTD
Division of HOLDEN Ltd ACN 006 893 232
COPYRIGHT
Page 4 of 5
FITTING INSTRUCTIONS: - continued...
Refer to Figure 6 for the following:
8. Adjust the position of the roof bars so that the length of
the roof bar is the same on both sides of the vehicle .
9. Place a split washer and flat washer onto the screw.
Insert the screw into the hole in the roof bar support.
Insert the security bit (1) through the hole in the roof bar
(2) and tighten the screw.
10. Fit the strip (3) to the upper channel in the roof bar.
11. Tighten the bolt under the roof bar (4 places). Refer to
Figure 7.
CAUTION: Protect the surface of the vehicle to
prevent damage.
12. Install the sealing strip (1) under the roof bar (4 places).
Ensure that there is no gap between the sealing strip
and the roof bar support. Trim the sealing strip level with
the end of the roof bar. Refer to Figure 8.
1
FIGURE 8
1
2
3
FIGURE 7
FIGURE 9
FITTING INSTRUCTIONS FOR
VY - VZ WAGON ROOF BARS
FD1317
15NOV04
Reproduction in whole or part
prohibited without written approval
HOLDEN LTD
Division of HOLDEN Ltd ACN 006 893 232
COPYRIGHT
VY - VZ WAGON ROOF BARS
PARTS LIST
PART NUMBER DESCRIPTION QUANTITY
92171977 ROOF BAR KIT 1
ROOF BAR 2
MOUNTING KIT, LH & RH (FRONT) 1
MOUNTING KIT, LH & RH (REAR) 1
FD1317 FITTING INSTRUCTIONS 1
FD796 PROOF OF WARRANTY CARD 1
FIGURE 10
1
1
FIGURE 11
FITTING INSTRUCTIONS: - continued...
113.Install the end caps (1) to the roof bar (4 places). Ensure
that the tab is positioned upwards. Refer to Figure 9.
14. Close the tab (1) on the end cap (4 places). Refer to
Figure 10.
Page 5 of 5