FITTING INSTRUCTIONS FOR
XC BARINA FRONT SEAT INSERTS
(3 DOOR)
Part No. 92144469
COPYRIGHT
Page 1 of 2
FD1015-01
HOLDEN SERVICE PARTS OPERATIONS
Reproduction in whole or part
prohibited without written approval
Division of HOLDEN Ltd ACN 006 893 232
FITTING INSTRUCTIONS
1. Remove the head restraint assembly and select the seat back insert with the opening for the tilt
seat lever for the driver's or passenger's side seats.
2. Insert the head restraint mounting assembly through the 2 holes in the front seat insert upper and
re-install the head restraint. Refer View A, Page 2.
3. Fit the insert over the tilt lever and then firmly and squarely, pull seat back insert down into
position over the top of the seat back. Insert the lower part between the seat cushion and the seat
back and pull the lower part of the insert through, maintaining alignment with the seat back. Refer
Section A-A & View C Page 2.
4. Using the alcohol wipe, thoroughly clean the seat cover vinyl area of the velcro strip contact
surface area of the seat back. Allow the surface to dry before proceeding. Refer View C, Page 2.
5. Peel off the protective backing from the velcro strip and with the insert pulled tight, adhere the
velcro strip to the lower part of the seat. Refer View C, Page 2.
6. Fit the seat cushion insert by feeding the rear fastening buckles between seat cushion and seat
back. Refer Section A-A & View C, Page 2.
7. Using the alcohol wipe, thoroughly clean the seat cover vinyl area of the velcro strip contact
surface area of the seat cushion. Allow the surface to dry before proceeding. Refer View D, Page
2.
8. Ensuring that the seat cushion insert is aligned, peel off the protective backing from the velcro
strip and adhere it to the rear of the seat cushion. Refer View D Page 2.
9. Feed front fastening buckles under the seat, above and over all adjustments and wiring
assemblies. Refer View B, Page 2.
10. Fasten the buckles and tension by pulling loose end of the fastening strap. Tuck excess tape out
of sight.
WASHING INSTRUCTIONS
Dry cleaning recommended.
Hand wash with approved wool detergents. Do not soak for prolonged periods.
Rinse and gentle spin (fleece out) dry away from direct heat, preferably flat in shaded area.
While still damp, gently pull into shape and brush with a coarse stiff brush to restore pile.
FD1015
06AP01
FITTING INSTRUCTIONS FOR
XC BARINA FRONT SEAT INSERTS
FD1015-02
HOLDEN SERVICE PARTS OPERATIONS
Page 2 of 2
COPYRIGHT
Reproduction in whole or part
prohibited without written approval
Division of HOLDEN Ltd ACN 006 893 232
SEATBACK SEATBACK
SEAT
CUSHION
SEAT
CUSHION
SEAT CUSHION VELCRO STRIP
MOUNTING AREA. CLEAN
CONTACT AREA THOROUGHLY
SEAT BACK VELCRO STRIP
MOUNTING AREA. CLEAN
CONTACT AREA THOROUGHLY
PEEL OFF ADHESIVE PROTECTIVE
BACKING TAPE AND ADHERE VELCRO
TO SEAT CUSHION
PEEL OFF ADHESIVE
PROTECTIVE BACKING TAPE
AND ADHERE VELCRO TO
SEAT BACK.
A-A
SECTION
SEATBACK
SEAT
CUSHION
SEAT CUSHION
INSERT
SEAT
INSERT
BACK
INSERT
VELCRO
STRIP
VELCRO
STRIP
TUCK 20-30mm OF
SEAT INSERT IN
BETWEEN SEAT
CUSHION AND
SEAT BACK VIEW B
VIEW CVIEW D
A
B
C
FRONT
ROUTE FASTENING CLIPS
UNDER THE SEAT, ABOVE
ALL MECHANISMS AND
WIRING ASSEMBLIES
A
A
BACKREST
INSERT
PULL INSERT DOWN
DESCRIPTION QTY
COVER INSERT -SEAT BACK 2
COVER INSERT -SEAT CUSHION 2
ALCOHOL WIPES 2
FITTING INSTRUCTIONS - FD1015 1
PARTS LIST
VIEW A
HEAD RESTRAINT
SEAT BACK
TILT LEVER
FD1015
06AP01