SECTION 12C - METER AND GAUGE

Service Precaution

Meter Assembly

General Description

Layout for Meters/Gauges, Warning Lights,

Indicator Lights and Illumination Lights

Table for Meter/Gauge Connector Terminal

Connections

Removal

Installation

Warning Light Bulb, Indicator Light Bulb,

Illuminatio Light Bulb, A/T Shift Indicator

Light Bulb

Removal

Installation

Vehicle Speed Sensor

Removal

Installation

Fuel Tank Unit

Removal and Installation

SERVICE PRECAUTION

WARNING: THIS VEHICLE HAS A SUPPLEMENTAL

RESTRAINT SYSTEM (SRS). REFER TO THE SRS

COMPONENT AND WIRING LOCATION VIEW IN

ORDER TO DETERMINE WHETHER YOU ARE

PERFORMING SERVICE ON OR NEAR THE SRS

COMPONENTS OR THE SRS WIRING. WHEN YOU

ARE PERFORMING SERVICE ON OR NEAR THE

SRS COMPONENTS OR THE SRS WIRING, REFER

TO THE SRS SERVICE INFORMATION. FAILURE TO

FOLLOW WARNINGS COULD RESULT IN POSSIBLE

AIR BAG DEPLOYMENT, PERSONAL INJURY, OR

OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.

CAUTION: Always use the correct fastener in the

proper location. When you replace a fastener, use

ONLY the exact part number for that application.

HOLDEN will call out those fasteners that require a

replacement after removal. HOLDEN will also call

out the fasteners that require thread lockers or

thread sealant. UNLESS OTHERWISE SPECIFIED,

do not use supplemental coatings (Paints, greases,

or other corrosion inhibitors) on threaded fasteners

or fastener joint interfaces. Generally, such

coatings adversely affect the fastener torque and

the joint clamping force, and may damage the

fastener. When you install fasteners, use the correct

tightening sequence and specifications. Following

these instructions can help you avoid damage to

parts and systems.

METER ASSEMBLY

GENERAL DESCRIPTION

The meter assembly has the speedometer, tachometer,

engine coolant temperature gauge, fuel gauge and

warning/indicator lights. These gauges and warning/

indicator lights can be removed and installed from the

back side of meter assembly.

LAYOUT FOR METERS/GAUGES,

WARNING LIGHTS, INDICATOR

LIGHTS AND ILLUMINATION LIGHTS

Meter Assembly (Front View)

821R100018

Legend

EndOFCallout

(1) Tachometer

(2) Turn Signal, Brake and High Beam Indicators

(3) Speedometer

(4) Fuel Gauge

(5) Res et Button

(6) ABS Failure and 4WD Engaged Indicators

(7) A/T Shift Indicator

(8) TOD Indica tor

(9) Engine Coolant Temperature Gauge

Meter Assembly (Rear View)

821R100019

Legend

EndOFCallout

(10) Illu mi nati on Lig ht

(11) LCD Light

(12) Illu mi nati on Lig ht

(13) Illumination Light

(14) Illumination Light

TABLE FOR METER/GAUGE CONNECTOR TERMINAL CONNECTIONS

821RY00114

Connector No. I–10

Terminal Function

1—

2—

3 TOD rear position indicator light

4—

5 TOD auto position indicator light

6—

7 TOD front position indicator light

8 3 position (A/T)

9 D position (A/T)

10 2 position (A/T)

11 AIR BAG warning light

12 Ground

13 Battery (+)

14 Starter switch (+)

15 OIL TEMP warning light

16 Seat belt warning light

17 Charge warning light

18 —

19 —

20 —

21 L position (A/T)

22 ABS indicator light

23 4WD indicator light

24 —

25 REDUCED POWER warning light

26 Oil pressure warning light

27 CHECK TRANS warning light

28 —

29 CHECK T.O.D warning light

30 Engine coolant temperature gauge

Connector No. I–9

Terminal Function

1 R position (A/T)

2+IGN (A/T)

3 N position (A/T)

4 P position (A/T)

5 Illuminati on (+)

6 Tachometer

7 Speedometer

8 Turn signal indicator light (Left)

9 Brake warning light

10 High-b eam indic ato r light (+)

11 High-b eam indica to r light (-)

12 Turn signal indicator light (Right)

13 Turn signal indicator light (-)

14 —

15 Illumi nati on (-)

16 Ground

Connector No. I–2

Terminal Function

1Starter switch (+)

2—

3 Fuel gauge

4—

5 CRUISE SET indicator light

6—

7—

8—

9—

10 —

11 —

12 WINTER DRIVE indicator light

13 POWER DRIVE indicator light

14 —

REMOVAL

1. Disconnect the battery ground cable.

2. Remove the Dash Side Trim Panel –RH (3).

3. Remove the lower cover Assembly(2).

• Refer to the Instrument Panel Assembly in Body

Structure section.

4. Remove the Instrument Facia (1).

• Refer to the Instrument Panel Assembly in Body

Structure section.

821RW292-1

5. Remove four fixing screws and disconnect the

meter connectors to remove the meter assembly(4).

825RW284

CAUTION: The removed meter assembly should be

placed upright or with its face side up.

INSTALLATION

To install, follow the removal steps in the reverse order.

WARNING LIGHT BULB, INDICATOR LIGHT BULB, ILLUMINATION

LIGHT BULB, A/T SHIFT INDICATOR LIGHT BULB

REMOVAL

1. Disconnect the battery ground cable.

2. Remove the meter assembly(1).

• Refer to the Meter Assembly removal steps in

Meter and Gauge section.

3. Hold the bulb socket by hand and rotate it

counterclockwise to remove the socket & bulb(2)

from the meter body.

825RW059

INSTALLATION

To install, follow the removal steps in the reverse order.

VEHICLE SPEED SENSOR

REMOVAL

1. Disconnect the battery ground cable.

2. Remove the vehicle speed sensor(1).

• Disconnect the connector.

• Rotate the sensor counterclockwise.

225R200001

INSTALLATION

To install, follow the removal steps in the reverse order,

noting the following point.

1. Tighten the vehicle speed sensor to the specified

torque.

Torque: 25 N·m (18 lbft)

FUEL TANK UNIT

REMOVAL AND INSTALLATION

Refer to Engine Fuel section.