SECTION 12D - ENTERTAINMENT
Service Precaution
Cigarette Lighter
General Description
Removal
Installation
Digital Clock
Removal
Installation
Rod Type Antenna
Removal
Installation
Radio
Removal
Installation
Speaker
Front Speaker
Tweeter Assembly
Rear Speaker
Rear Door Speaker
Accessory Socket
Front Accessory Socket
Rear Accessory Socket
Horn
Removal
Installation
SERVICE PRECAUTION
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFER
TO THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
HOLDEN will call out those fasteners that require a
replacement after removal. HOLDEN will also call
out the fasteners that require thread lockers or
thread sealant. UNLESS OTHERWISE SPECIFIED,
do not use supplemental coatings (Paints, greases,
or other corrosion inhibitors) on threaded fasteners
or fastener joint interfaces. Generally, such
coatings adversely affect the fastener torque and
the joint clamping force, and may damage the
fastener. When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.
CIGARETTE LIGHTER
GENERAL DESCRIPTION
When the cigarette lighter is pushed in with the starter
switch at either “ACC" or “ON" position, a circuit is
formed in the cigarette lighter case to heat the lighter
coil.
The cigarette lighter springs back to its original position
after the lighter coil is heated.
REMOVAL
1. Disconnect the battery ground cable.
2. Remove the lower cluster assembly (1).
• Refer to the Instrument Panel Assembly in Body
Structure section.
3. Remove the cigarette lighter assembly (2).
• Disconnect the connectors.
• Remove the socket (3).826RW004-1
INSTALLATION
To install, follow the removal steps in the reverse order,
noting the following point:
1. When installing the bezel, align the projected portion
of the socket with the notch of the bezel.
DIGITAL CLOCK
REMOVAL
1. Disconnect the battery ground cable.
2. Remove the dash side trim panel-LH (1).
• Refer to Instrument Panel Assembly in Body
Structure section.
3. Remove the lower cover assembly (2).
• Refer to instrument Panel Assembly in Body
Structure section.
821RW293-1
4. Remove the meter cluster assembly (3).
Refer to instrument Panel Assembly in Body
Structure section.
5. Remove the digital clock (4).
• Remove the fixing screw.
• Disconnect the connector.
821RW291
INSTALLATION
To install, follow the removal steps in the reverse order.
ROD TYPE ANTENNA
REMOVAL
1. Disconnect the battery ground cable.
2. Turn the antenna rod (3) counterclockwise to
remove it.
3. Remove three screws and nine clips to remove the
fender inner liner (6).
4. Disconnect the feeder cable connector (7) at the
inside of the vehicle.
5. Turn the lock nut (2) counterclockwise and remove it
together with the base mold (1).
6. Pull down and remove the housing (4) from the
panel.
7. Pull and remove the cable with the grommet (5).
890R100019
INSTALLATION
To install, follow the removal steps in the reverse order.
RADIO
REMOVAL
1. Disconnect the battery ground cable.
2. Remove the lower cluster assembly (1).
• Refer to Instrument Panel Assembly in Body
Structure section.
890RW086
3. Remove the radio (2).
• Remove the two fixing screws.
• Disconnect the connector (4) and the antenna
cable (3).
890RW085
INSTALLATION
To install, follow the removal steps in the reverse order.
SPEAKER
FRONT SPEAKER
Removal
1. Disconnect the battery ground cable.
2. Pull the grille (1) to release the locks and then
remove it.
3. Remove four screws and disconnect the connector
(3) to remove the speaker (2).
890RX012
Installation
To install, follow the removal steps in the reverse order.
TWEETER ASSEMBLY
Removal
1. Disconnect the battery ground cable.
2. Remove the front door trim pad (2).
• Refer to Front Window Regulator, Glass And
Glass Run in Body Structure section:
3. Remove the tweeter (1).
• Disconnect the connector.
635RW009
Installation
To install, follow the removal steps in the reverse order.
REAR SPEAKER
Removal
1. Disconnect the battery ground cable.
2. Remove the roof rear lining (1).
• Release the locks and clips.
3. Remove the speaker (2).
• Remove the four screws.
• Disconnect the connector (3).
890RX028
Installation
To install, follow the removal steps in the reverse order.
REAR DOOR SPEAKER
Removal
1. Disconnect the battery ground cable.
2. Remove the rear door speaker.
• Refer to Rear Window Regulator, Glass and
Glass Run in Body Structure section.
890R100020
Installation
To install, follow the removal steps in the reverse order.
ACCESSORY SOCKET
FRONT ACCESSORY SOCKET
Removal
1. Disconnect the battery ground cable.
2. Remove the lower cluster assembly (1).
3. Remove the front accessory socket (4).
• Disconnect the connectors (2).
• Pull out the front accessory socket from the
socket cover (3).
810RW326
Installation
To install, follow the removal steps in the reverse order,
noting the following point:
REAR ACCESSORY SOCKET
Removal
1. Disconnect the battery ground cable.
2. Remove the rear accessory socket (2).
• Disconnect the connectors (1).
• Pull out the front accessory socket from the
sock et co ver (3) .
810RW004
Installation
To install, follow the removal steps in the reverse order.
HORN
REMOVAL
1. Disconnect the battery ground cable.
2. Remove the radiator grille.
• Refer to Engine Hood and Fender in Body
Structure section.
3. Remove the horn (1).
• Disconnect the connector.
• Remove the horn mounting bolt.
828RX001
INSTALLATION
To install, follow the removal steps in the reverse order.