SECTION 12M1 - SEAT BELT SYSTEM

Service Precaution

Front Seat Belt

Front Seat Belt and Associated Parts

Removal

Inspection

Installation

Front Seat Belt

Front Seat Belt and Associated Parts

Removal

Inspection

Installation

Front Seat Buckle Assembly

Removal

Installation

Rear Center Seat Belt / Buckle Assembly

and Associated Parts

Removal

Installation

Child Seat Anchor Bracket

(Child Restraint)

General Description

Child Seat Anchor Bracket and

Associated Parts

Installation

Main Data and Specifications

SERVICE PRECAUTION

WARNING: THIS VEHICLE HAS A SUPPLEMENTAL

RESTRAINT SYSTEM (SRS). REFER TO THE SRS

COMPONENT AND WIRING LOCATION VIEW IN

ORDER TO DETERMINE WHETHER YOU ARE

PERFORMING SERVICE ON OR NEAR THE SRS

COMPONENTS OR THE SRS WIRING. WHEN YOU

ARE PERFORMING SERVICE ON OR NEAR THE

SRS COMPONENTS OR THE SRS WIRING, REFER

TO THE SRS SERVICE INFORMATION. FAILURE TO

FOLLOW WARNINGS COULD RESULT IN POSSIBLE

AIR BAG DEPLOYMENT, PERSONAL INJURY, OR

OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.

CAUTION: Always use the correct fastener in the

proper location. When you replace a fastener, use

ONLY the exact part number for that application.

HOLDEN will call out those fasteners that require a

replacement after removal. HOLDEN will also call

out the fasteners that require thread lockers or

thread sealant. UNLESS OTHERWISE SPECIFIED,

do not use supplemental coatings (Paints, greases,

or other corrosion inhibitors) on threaded fasteners

or fastener joint interfaces. Generally, such

coatings adversely affect the fastener torque and

the joint clamping force, and may damage the

fastener. When you install fasteners, use the correct

tightening sequence and specifications. Following

these instructions can help you avoid damage to

parts and systems.

Techline

FRONT SEAT BELT

FRONT SEAT BELT AND ASSOCIATED PARTS

760R100045

Legend

EndOFCallout

REMOVAL

1. Disconnect the battery ground cable.

2. Remo ve the si ll plate (Fr on t & Rear).

3. Remove the anchor cover and seat belt lower

anchor bolt.

4. Remove the lower center pillar trim cover.

5. Remove the door seal finisher (Front & Rear).

6. Remove the upper center pillar trim cover.

7. Remo ve the se at belt uppe r anchor bol t.

8. Remo ve the re tract or fixi ng bolt .

9. Remo ve the se at belt as sem bl y.

10. Remo ve the adjus table should er ancho r assem bl y.

• Remove the two fixing bolts.

(1) Door Seal Finisher (Front & Rear)

(2) Adj us table Shou lde r Anchor Asse mbl y

(3) Seat Belt Upper Anchor Bolt

(4) Upper Center Pillar Trim Cover

(5) Front Seat Belt Assembly

(6) Anchor Cover

(7) Seat Belt Lower Anchor Bolt

(8) Lower Center Pillar Trim Cover

(9) Retractor

(10) Rear Sill Pl ate

(11) F r ont Si ll Plate

INSPECTION

If any of the following faults are found, replace the seat

belt assembly.

• Deformed or malfunctioning adjustable shoulder

anchor (1).

• Resticted or rough movement of the upper/lower

anchors (2).

• Damaged and/or deformed guide(3).

• Damaged and/or deformed tongue (4).

• Damaged and/or frayed of webbing (5).

• Deformed retractor bracket (6).

• Seat belt not fully rewind (7).

• Resistance or abnormal sound when seat belt is

extended and retracted (7).

760R100032

Inspection of retractor

1. ELR (Emergency Locking Retractor) lock inclining

angle check.

• When the retractor is moved gently from its install

position, make sure it is not locked within 15° in

any directions, and it remains locked at 45° or

larger.

2. ELR lock check.

• Ensure the seat belt does not lock when it is

pulled slowly from the retractor, but the seat belt

locks when it is pulled quickly from the retractor

CAUTION: Do not disassemble the retractor.

INSTALLATION

To install, follow the removal steps in the reverse order,

noting the foll owi ng poi nts.

1. Tighten the adjustable shoulder anchor assembly

fixing bolts to the specified torque.

Torque: 39N·m (4.0kg·m/29lbft)

2. Tighten the seat belt anchor bolts (Upper & Lower)

and the retractor fixing bolts to the specified torque.

Torque: 39N·m (4.0kg·m/29lbft)

FRONT SEAT BELT

FRONT SEAT BELT AND ASSOCIATED PARTS

760R100049

Legend

EndOFCallout

REMOVAL

1. Disconnect the battery ground cable.

2. Remo ve the tailgat e weathe r stri p.

3. Remove the rear end floor trim cover.

4. Remo ve the lug gag e room light.

• Remove the luggage room light lens (1) and the

fixing screw.

(1) Adj us table Shou lde r Anchor Asse mbl y

(2) Seat Belt Upper Anchor Bolt

(3) Slider Plate Trim Assembly

(4) Upper Quarter Trim Cover

(5) Rear Roof Trim Cover

(6) Tailgate Weather Strip

(7) Rear End Floor Trim Cover

(8) Lower Quarter Trim Cover

(9) Seat Belt Lower Anchor Belt

(10) Anchor Cover

(11) Rear Seat Belt Assembly

(12) Screw

(13) Retractor

(14) Rear Sill Pl ate

(15) Rear Door Seal Finisher

• Disconnect the luggage room light connector.

825RW100

5. Remove the rear roof trim cover.

• Pry the trim cover clips free from the body panel.

6. Remove the rear sill plate.

7. Remove the anchor cover and the lower anchor

bolt.

8. Remove the upper and lower quarter trim cover.

• Refer to Interior Trim Panel (LWB) in Exterior/

Interior Trim section.

9. Remove the slider plate trim assembly (2).

• Remove the two fixing screws from the adjustable

shoulder anchor (1).

• Pull out the seat belt through the hole (3) on the

slider plate trim.

755RW069

10. Remove the seat belt upper anchor bolt.

11. Remove the retractor.

12. Remove the rear seat belt assembly.

13. Remove the adjustable shoulder anchor assembly.

• Remove the two fixing bolts.

INSPECTION

f any of the following fauts are found, replace the seat

belt assembly.

• Deformed or malfunctioning adjustable shoulder

anchor (1).

• Resticted or rough movement of the upper/lower

anchors (2).

• Damaged and/or deformed guide(3).

• Damaged and/or deformed tongue (4).

• Damaged and/or frayed of webbing (5).

• Deformed retractor bracket (6).

• Seat belt not fully rewind (7).

• Resistance or abnormal sound when seat belt is

extended and retracted (7).

760R1000051

Inspection of retractor

1. ELR (Emergency Locking Retractor) lock inclining

angle check.

• When the retractor is moved gently from its

installing position, make sure it is not locked

within 15° in any directions, and it remains locked

at 45° or larger.

2. ELR lock check.

• Ensure the seat belt does not lock when it is

pulled slowly from the retractor.

• Ensure the seat belt locks when it is pulled

quickly from the retractor.

CAUTION: Do not disassemble the retractor.

INSTALLATION

To install, follow the removal steps in the reverse order,

noting the following points.

1. Tighten the adjustable shoulder anchor assembly

and retractor fixing bolts to the specified torque.

Torque: 39N·m (4.0kg·m/29lbft)

2. Tighten the seat belt anchor bolts (Upper & Lower)

and the retractor fixing bolts to the specified torque.

Torque: 39N·m (4.0kg·m/29lbft)

FRONT SEAT BUCKLE ASSEMBLY

REMOVAL

1. Disconnect the battery ground cable.

2. Disconnect the seat belt warning connector (driver's

side) and remove a clip.

3. Remove the front seat buckle assembly (1).

760RY00016

INSTALLATION

To install, follow the removal steps in the reverse order,

noting the foll owi ng poi nt.

1. Tighten the buckle anchor bolt to the specified

torque.

Torque: 39N·m (4.0kg·m/29lbft)

REAR CENTER SEAT BELT / BUCKLE ASSEMBLY

REAR CENTER SEAT BELT / BUCKLE ASSEMBLY AND ASSOCIATED PARTS

755R200006

Legend

EndOFCallout

REMOVAL

1. Remove the rear cushion frame assembly.

• Refer to Rear Seat Assembly in Seats section.

2. Remove the rear seat lock assembly and rear seat

belt buckle assembly.

INSTALLATION

To install, follow the removal steps in the reverse order,

noting the foll owi ng poi nt.

1. Tighten the rear seat lock assembly and rear seat

belt buckle assembly fixing bolts to the specified

torque.

Torque: 39N·m (4.0kg·m/29lbft)

NOTE: Removal and installation procedure of rear

center seat belt assembly same as rear seat belt buckle

assembly procedures.

(1) Rear Seat Lock Assembly

(2) Rear Seat Belt Buckle Assembly (3) Rear Cushion Frame Assembly

CHILD SEAT ANCHOR BRACKET (CHILD RESTRAINT)

GENERAL DESCRIPTION

Plastic plug is provided at two or three places on the

luggage floor panel.

Remove the center plug fom the floor panel.

Install the bracket to the hole where the plug is

removed.

Alternatively, the bracket may be installed in the

right-hand or left-hand plug hole.

CHILD SEAT ANCHOR BRACKET AND ASSOCIATED PARTS

760R100042

Legend

EndOFCallout

INSTALLATION

1. Turn the plug counterclockwise to remove it.

2. Install the bracket such that the belt hook hole is

facing toward the front of the vehicle.

3. Tighten the fixing bolt to the specified torque.

Torque: 20N·m (2.0kg·m/14lbft)

(1) Rear Seat

(2) Lugga ge Fl oo r carpet (3) Child Seat Anchor Bracket

(4) Anchor Blanking Plug

MAIN DATA AND SPECIFICATIONS

Torque Specifications

760R100050

760R100044