SECTION 8A - LIGHTING SYSTEM
Service Precaution
Headlight Bulb
Removal
Installation
Headlight Assembly
Removal
Installation
Headlight Adjustment
Fog Light Bulb
Removal
Installation
Fog Light Assembly
Removal
Installation
Fog Light Adjustment
Clearance Light Bulb
Removal
Installation
Front Combination Light Assembly
Removal
Installation
Taillight Bulb
Removal
Installation
License Plate Light Bulb (Bumper Type)
Removal
Installation
License Plate Light Bulb (Tailgate Type)
Removal
Installation
Stoplight Bulb
Removal
Installtion
High Mounted Stoplight Assembly
(4Door Model)
Removal
Installation
High Mounted Stoplight Bulb
(4Door Model)
Removal
Installation
High Mounted Stoplight Assembly
(2Door Model)
Removal
Installation
High Mounted Stoplight Bulb
(2Door Model)
Removal
Installation
Backup Light Bulb
Removal
Installation
Front Turn Signal Light Bulb
Removal
Installation
Side Turn Signal Light Bulb
Removal
Installation
Rear Turn Signal Light Bulb
Removal
Installation
Dome Light Bulb
Removal
Installation
Courtesy Light Bulb
Removal
Installation
Map Light Bulb
Removal
Installation
Luggage Room Light Bulb (4Door Model)
Removal
Installation
Luggage Room Light Bulb (2Door Model)
Removal
Installation
HVAC Bezel Illumination Light Bulb
Removal and Installation
Shift Lever Illumination Light Bulb (A/T)
Removal
Installation
Ashtray Illumination Bulb
Removal
Installation
Starter Switch
Removal and Installation
Lighting Switch (Combination Switch)
Removal and Installation
Dimmer·Passing Switch
(Combination Switch)
Removal and Installation
Door Switch
Removal
Installation
Rear Defogger Switch
Removal
Installation
Key Remind Switch (Starter Switch)
Removal and Installation
Hazard Warning Light Switch
Removal
Installation
Stoplight Switch
Removal and Installation
4WD Switch
Removal
Installation
Backup Light Switch (M/T)
Removal
Installation
Turn Signal Light Switch
(Combination Switch)
Removal and Installation
Light and Bulb Specifications (4Door Model ·
Spear Tyre Under Mount Type)
Light and Bulb Specifications (4Door Model ·
Spear Tyre Tail Gate Type)
Light and Bulb Specifications
(2Door Model)
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFER
TO THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or
other corrosion inhibitors) on threaded fasteners
or fastener joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may dama ge the fastener.
When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.
Headlight Bulb
Removal
1.Disconnect the battery ground cable.
2.Remove the headlight bulb.
•Disconnect the connector (3).
•Remove the socket retaining ring (1) by turning it
counterclockwise.
•Remove the cup (2).
•Remove the spring.
CAUTION: The halogen light bulb produces heat
and temperature rises high, therefore, if the glass
surface is contaminated it will be burnt by heat
leaving stains which will not come out. This may
reduce the illuminating power or damage the bulb
due to thermal deformation during evaporation. In
order to prevent this problem, do not touch the
glass surface with your fingers.
801RW026
Installation
To install, follow the removal steps in the reverse order.
Headlight Assembly
Removal
1.Disconnect the battery ground cable.
2.Remove the radiator grille (1).
•Remove eight clips and a screw.
3.Remove the side marker light (3).
•Remove three screws.
•Disconnect the connector.
4.Remove the headlight assembly (2).
•Disconnect the connector.
•Remove four screws.
825RW283
Installation
To install, follow the removal steps in the reverse order.
CAUTION: After installing the headlight, be sure to
adjust the headlight aim.
Headlight Adjustment
Preparation
Place the vehicle with 1 – person in driver seat, on a
lev el surface and chec k to see if the inflation pressure of
the tires iscorrect, the linses are clean, the battery is
sufficiently charged, and adjust to place vehicle by using
the screen .
1. Set up the screen (1) on a leve surface.
2. Put on the screen at right angles to the center line
(3).
3. Adjust the center of the vehicle (2) to the center line
on floor.
801RX018
4. Keep the vehicle (2) 3m (9.8 ft) apart from the
sc re e n (1).
5. Toward the screen from the bulb center mark of
headlight, extend a parallel line (A) to the floor and
draw a vertical line (V) at an intersection point of
screen and a parallel line (A).
801RW00001
6. Measure a height (H) from the bulb mark of
headlight to the floor and draw a horizontal line on
the screen.
7. Turn on the low beam of headlight.
8. Adjust the bending point to the vertical line (V) by
horizontal adjustment and adjust cut line 21mm
(0.83in) below from horizontal line (H) by vertical
adjustment.
801RX013
Vertical Adjustment
Use a screwdriver for vertical adjustment.
825RW278
Horizontal Adjustment
Use a screwdriver for horizontal adjustment.
825RW277
Fog Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the fog light bulb (2).
• Open the rear cover (1).
• Remove the dust cover.
• Disconnect the bulb connector.
• Remove the clip (3).
801RW002
Installation
To install, follow the removal steps in the reverse order.
Fog Light Assembly
Removal
1.Disconnect the battery ground cable.
2.Remove the fog light assembly (1).
•Disconnect the connector.
•Remove two nuts from the bracket.
801RW021
Installation
To install, follow the removal steps in the reverse order.
CAUTION: After installing the fog light, be sure to
adjust the fog light aim.
Fog Light Adjustment
Vertical Adjustment
Turn the adjusting screw with a scre wdriver to adjust the
aim of the fog light vertically.
801RW022
Clearance Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Disconnect the connector.
3. Remove the socket retaining ring by turning it
counterclockwise.
4. Remove the clearance light bulb (2).
• Remove the rubber cap.
• Pull out the b ulb socket (1).
801RW025
Installation
To install, follow the removal steps in the reverse order.
Front Combination Light Assembly
Removal
1.Disconnect the battery ground cable.
2.Remove the side combination light.
•Refer to Side Marker Light Bulb in this section.
3. Disconnect the connector.
Installation
To install, follow the removal steps in the reverse order.
Taillight Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the rear combination light assembly (1).
• Remove three screws.
3. Pull out the rear combination light assembly to ward
you.
825RX053
4. Remove the bulb holder (2).
• Remove the two wing nuts (1).
825RX054
• Remove the bulb (3) by turning it
counterclockwise while pushing it at the same
time.
825RX055
Installation
To install, follow the removal steps in the reverse order.
License Plate Light Bulb (Bumper Type)
Removal
1. Disconnect the battery ground cable.
2. Remove the lens cover (3).
• Remove two screws.
3. Remove the lens (2).
4. Remove the bulb (1).
• Pull out the bulb from the sock et.
825RW070
Installation
To install, follow the removal steps in the reverse order.
License Plate Light Bulb (Tailgate Type)
Removal
1. Disconnect the battery ground cable.
2. Remove the lens cover (3).
• Remove two screws.
3. Remove the bulb (2).
• Pull out the b ulb from the socket (1).
803RW014
Installation
To install, follow the removal steps in the reverse order.
Stoplight Bulb
Removal
1. Remo ve the bulb holder (2).
• Remove the two wing nuts (1).
825RX054
• Remove the bulb (3) by turning it
counterclockwise while pushing it at the same
time.
825RX058
Installtion
To install, follow the removal steps in the reverse order.
High Mounted Stoplight Assembly (4Door Model)
Removal
1. Disconnect the battery ground cable.
2. Remove the high mount stoplight assembly (2).
• Remove the cover (3).
• Disconnect the connectors (1).
• Remove two screws.
803RX001
Installation
To install, follow the removal steps in the reverse order.
High Mounted Stoplight Bulb (4Door Model)
Removal
1. Disconnect the battery ground cable.
2. Remove the cover.
3. Remove the bulb (1).
• Remove the socket by turning it
counterclockwise.
825RW071-1
Installation
To install, follow the removal steps in the reverse order.
High Mounted Stoplight Assembly (2Door Model)
Removal
1. Disconnect the battery ground cable.
2. Remove the high mounted stoplight assembly (1).
• Remove the two screws.
• Pull out the high mounted stoplight assembly (1).
• Disconnect the connectorb (2) .
803RX009
Installation
To install, follow the removal steps in the reverse order.
High Mounted Stoplight Bulb (2Door Model)
Removal
1.Disconnect the battery ground cable.
2.Remove the cover (2).
3.Remove the bulb (1).
803RX002-1
Installation
To install, follow the removal steps in the reverse order.
Backup Light Bulb
Removal
1.Disconnect the battery ground cable.
2.Remove the rear combination light assembly.
•Refer to the Taillight Bulb removal step 2 in this
section.
3. Remo ve the bulb holder (2).
• Remove the two wing nuts (1).
825RX054
• Remove the bulb (3) by turning it
counterclockwise while pushing it at the same
time.
825RX056
Installation
To install, follow the removal steps in the reverse order.
Front Turn Signal Light Bulb
Removal
1.Disconnect the battery ground cable.
2.Remove the radiator grille.
•Refer to Engine Hood and Fender in section.
3. Remove the front turn signal light (2).
• Remove three screws.
4. Remove the bulb (1).
• Remove the front turn signal light socket by
turning it counterclockwise.
• Remove the bulb by turning it counterclockwise
while pushing it at the same time.
825RW067
Installation
To install, follow the removal steps in the reverse order.
Side Turn Signal Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the side turnsignal light assembly.
• Pushing in the rear direction of vehicle, pull out it
toward you.
3. Remove the bulb (1) by turning i t countercloc kwise.
801RW024
Installation
To install, follow the removal steps in the reverse order.
Rear Turn Signal Light Bulb
Removal
1.Disconnect the battery ground cable.
2.Remove the rear combination light assembly.
•Refer to the Taillight Bulb in this section.
3. Remo ve the bulb holder (2).
• Remove the two wing nuts (2).
825RX054
• Remove the bulb (3) by turning it
counterclockwise while pushing it at the same
time.
825RX057
Installation
To install, follow the removal steps in the reverse order.
Dome Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the lens (2).
3. Remove the bulb (1).
• Pull out the bulb.
825RW075
Installation
To install, follow the removal steps in the reverse order.
Courtesy Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the lens (2).
3. Remove the bulb (1).
• Pull out the bulb.
825RW076
Installation
To install, follow the removal steps in the reverse order.
Map Light Bulb
Removal
1. Disconnect the battery ground cable.
2. Remove the lens (2).
3. Remove the bulb (1).
• Pull out the bulb.
825RW105
Installation
To install, follow the removal steps in the reverse order.
Luggage Room Light Bulb (4Door Model)
Removal
1. Disconnect the battery ground cable.
2. Remove the lens (2).
3. Remove the bulb (1).
• Pull out the bulb.
825RW077
Installation
To install, follow the removal steps in the reverse order.
Luggage Room Light Bulb (2Door Model)
Removal
1. Disconnect the battery ground cable.
2. Remove the lens (2).
3. Remove the bulb (1).
• Pull out the bulb.
805RX002
Installation
To install, follow the removal steps in the reverse order.
HVAC Bezel Illumination Light Bulb
Removal and Installation
Refer to Control Panel Illumination bulb in Heating,
Ventilation and Air Conditioning (HVAC) section.
Shift Lever Illumination Light Bulb (A/T)
Removal
1. Disconnect the battery ground cable.
2. Remove the console assembly.
• Remove four screws.
3. Remove the bulb (1).
• Turn the bulb socket counterclockwise.
• Pull out the bulb from the sock et.
825RW287
Installation
To install, follow the removal steps in the reverse order.
Ashtray Illumination Bulb
Removal
1.Disconnect the battery ground cable.
2.Remove the lower cluster panel(1).
•Refer to Instrument Panel Assembly in Body
Structure section.
3.Disconnector the connector (2).
4.Turn the socket counterclockwise to remove it then
pull out the bulb(3).
45RW013
Installation
To install, follow the removal steps in the reverse order.
Starter Switch
Removal and Installation
Refer to Lock cylinder in steering section.
Lighting Switch (Combination Switch)
Removal and Installation
Refer to Combination Switch in Steering section.
Dimmer·Passing Switch (Combination Switch)
Removal and Installation
Refer to Combination Switch in Steering section.
Door Switch
Removal
1.Disconnect the battery ground cable.
2.Remove the door switch (2).
•Remove the screw (1).
•Disconnect the connector (3).
825RW289
Installation
To install, follow the removal steps in the reverse order.
Rear Defogger Switch
Removal
1.Disconnect the battery ground cable.
2.Remove the meter cluster assembly (1).
•Refer to Instrument Panel Assembly in Body
Structure section.
3. Remove the rear defogger switch (2).
• Disconnect the switch connector.
• Push the lock from the back side of the meter
cluster assembly.
825RW280
Installation
To install, follow the removal steps in the reverse order.
Key Remind Switch (Starter Switch)
Removal and Installation
Refer to Lock Cylinder in Steering section.
Hazard Warning Light Switch
Removal
1.Disconnect the battery ground cable.
2.Remove the meter cluster assembly (1).
•Refer to Instrument Panel Assembly in Body
Structure section.
3.Remove the hazard warning switch (2).
•Disconnect the switch connector.
•Push the lock from the back side of the meter
cluster assembly.
825RW279
Installation
To install, follow the removal steps in the reverse order.
Stoplight Switch
Removal and Installation
Refer to Stoplight Switch in Brake section.
4WD Switch
Removal
1.Disconnect the battery ground cable.
2.Remove the meter cluster assembly (1).
•Refer to Instrument Panel Assembly in Body
Structure section.
3.Remove the 4WD switch (2).
•Disconnect the switch connector.
•Push the lock from the back side of the meter
cluster assembly.
825RW275-1
Installation
To install, follow the removal steps in the reverse order.
Backup Light Switch (M/T)
Removal
1.Disconnect the battery ground cable.
2.Remove the backup light switch (1).
•Disconnect the connector (2).
230RW010
Installation
To install, follow the removal steps in the reverse order,
noting the following point.
1.Apply liquid gasket to the screw portion of the switch
to prevent oil leak.
Turn Signal Light Switch (Combination Switch)
Removal and Installation
Refer to Combination Switch in Steering section.
Light and Bulb Specifications (4Door Model · Spear Tyre Under Mount Type)
810RX016
Legend
EndOFCallout
(1) Map Light
(2) Meter
(3) Fog Light
(4) Headlight/Clearance Light
(5) Front Turn Signal Light
(6) Side Turn Signal Light
(7) High Mounted Stoplight
(8) Luggage Room Light
(9) Dome Light
(10) Courtesy Light
(11) Stoplight
(12) Backup Light
(13) Taillight
(14) Rear Turn Signal Light
(15) License Plate Light
Light and Bulb Specifications (4Door Model · Spare Tyre Tail Gate Type)
810RX022
Legend
EndOFCallout
(1) Map Light
(2) Meter
(3) Fog Light
(4) Headlight/Clearance Light
(5) Front Turn Signal Light
(6) Side Turn Signal Light
(7) High Mounted Stoplight
(8) Luggage Room Light
(9) Dome Light
(10) Courtesy Light
(11) Stoplight
(12) Backup Light
(13) Taillight
(14) Rear Turn Signal Light
(15) License Plate Light
Light and Bulb Specifications (2Door Model)
801RX023
Legend
EndOFCallout
(1) Map Light
(2) Meter
(3) Fog Light
(4) Headlight/Clearance Light
(5) Front Turn Signal Light
(6) Side Turn Signal Light
(7) Do me Lig h t
(8) Courtesy Light
(9) Stoplight
(10) Taillight
(11) Backup Light
(12) Rear Turn Signal Light
(13) License Plate Light
(14) Luggage Room Light
(15) High Mounted Stoplight
Light and Bulb Specifications
Light Name Bulb No. Rated
Power Number of
Bulbs Lens Color Remarks
Headlight/Clearance Light — 60w/55w,
5w 2 White Halogen
Front Turn signal Light — 21w 2 Amber
Fog Light — 55w 2 White Halogen
Rear Turn Signal Light — 21w 2 Amber
Backup Light — 21w 2 White
Taillight — 5w 2 Red
Stoplight — 21w 2 Red
High Mounted Stoplight — 5w 4 Red
License Plate Light (Tailgate type) — 5w (5W) 1 (2) White
Map Light — 5w 2 White
Dome Light — 7w 1 White
Luggage Room Light (2Door Model) — 5w(3.4w) 1(1) White
Courtesy Light — 3.4w 4 White
Indicator/Warning
Light
Check Trans — 1.4w 1 Red Meter
A/T Oil Temp — 3w 1 Red Meter
Cruise Set — 1.4w 1 Green Meter
Power Drive — 1.4w 1 Amber Meter
Winter Drive — 1.4w 1 Green Meter
Turn Signal — 1.4w 2 Green Meter
High Beam — 1.4 w 1 Blue M ete r
ABS — 1.4w 1 Amber Meter
Seat Belt — 2w 1 Red Meter
Malfunction Indicator
(Check Engine) — 1.4w 1 Amber Meter
Low Fuel — 1.4w 1 Amber Meter
4WD — 1.4w 1 Green Meter
Oil Pressure — 1.4w 1 Red Meter
Brake System — 1.4w 1 Red Meter
Charge — 1.4w 1 Red Meter
A/T Shift Position — 1.4w 7 P,N,D,3,2,L
:Green
R: Amber
Meter
Air Bag — 2w 1 Red Meter
Illumination Light Meter — 3.4w 4 Meter
Shift lever — 1.4w 1 White Shift lever