SECTION 8C - ENTERTAINMENT
Service Precaution
Cigarette Lighter
General Description
Removal
Installation
Digital Clock
Removal
Installation
Rod Type Antenna
Removal
Installation
Radio
Removal
Installation
Speaker
Front Speaker
Tweeter Assembly
Rear Speaker (4Door Model)
Rear Speaker (2Door Model)
Accessory Socket
Front Accessory Socket
Rear Accessory Socket
Horn
Removal
Installation
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFER
TO THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
ISUZU will call out those fasteners that require a
replacement after removal. ISUZU will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or
other corrosion inhibitors) on threade d fasteners or
fasteners joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fasteners.
When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.
Cigarette Lighter
General Description
When the cigarette lighter is pushed in with the starter
switch at either “ACC" or “ON" position, a circuit is
formed in the cigarette lighter case to heat the lighter
coil.
The cigarette lighter springs back to its original position
after the lighter coil is heated.
Removal
1.Disconnect the battery ground cable.
2.Remove the lower cluster assembly (1).
•Refer to the Instrument Panel Assembly in Body
Structure section.
3.Remove the cigarette lighter assembly (2).
•Disconnect the connectors.
•Remove the socket (3).826RW004-1
Installation
To install, follow the removal steps in the reverse order,
noting the following point:
1.When installing the bezel, align the projected
portion of the socket with the notch of the bezel.
Digital Clock
Removal
1.Disconnect the battery ground cable.
2.Remove the dash side trim panel-LH (1).
•Refer to Instrument Panel Assembly in Body
Structure section.
3.Remove the lower cover assembly (2).
•Refer to instrument Panel Assembly in Body
Structure section.
821RW293-1
4.Remove the meter cluster assembly (3).
Refer to instrument Panel Assembly in Body
Structure section.
5. Remove the digital clock (4).
• Remove the fixing screw.
• Disconnect the connector.
821RW291
Installation
To install, follow the removal steps in the reverse or der.
Rod Type Antenna
Removal
1. Disconnect the battery ground cable.
2. Turn the antenna rod (2) counterclockwise to
remove it.
3. Remove three screws and nine clips to remove the
fender inner liner (4).
4. Disconnect the feeder cable connector at the inside
of the vehicle, remove the housing bracket screw
(1), turn the lock nut counterclockwise to remove it
together with the base mold and then remove the
housing (3).
890RX021
Installation
To install, follow the removal steps in the reverse or der.
Radio
Removal
1.Disconnect the battery ground cable.
2.Remove the lower cluster assembly (1).
•Refer to Instrument Panel Assembly in Body
Structure section.
890RW086
3. Remove the radio (2).
• Remov e the two fixing screws.
• Disconn ec t the conne cto r (4) and the antenna
cable (3).
890RW085
Installation
To install, follow the removal steps in the reverse or der.
Speaker
Front Speaker
Removal
1.Disconnect the battery ground cable.
2.Pull the grille (1) to release the locks and then
remove it.
3.Remove four screws and disconnect the connector
(3) to remove the speaker (2).
890RX012
Installation
To install, follow the removal steps in the reverse order.
Tweeter Assembly
Removal
1.Disconnect the battery ground cable.
2.Remove the front door trim pad (2).
•Refer to Front Window Regulator, Glass And
Glass Run in Body Structure section:
3. Remove the tweeter (1).
• Disconnect the connector.
635RW009
Installation
To install, follow the removal steps in the reverse or der.
Rear Speaker (4Door Model)
Removal
1. Disconnect the battery ground cable.
2. Remove the roof rear lining (1).
• Release the locks and clips.
3. Remove the sp eaker (2).
• Remov e the four screws.
• Disconnect the connector (3).
890RX028
Installation
To install, follow the removal steps in the reverse order.
Rear Speaker (2Door Model)
Removal
1. Disconnect the battery ground cable.
2. Pull the grille (1) to release the locks clips and then
remove it.
3. Remove four screws and disconnect the connector
(3) to remove the speaker (2).
890RW048-1
Installation
To install, follow the removal steps in the reverse or der.
Accessory Socket
Front Accessory Socket
Removal
1. Disconnect the battery ground cable.
2. Remove the lower cluster assembly (1).
3. Remove the front accessory socket (4).
• Disconnect the connectors (2).
• Pull out the front accessory socket from the
socket cover (3).
810RW326
Installation
To install, follow the removal steps in the reverse order,
noting the following point:
Rear Accessory Socket
Removal
1. Disconnect the battery ground cable.
2. Remove the rear accessory socket (2).
• Disconnect the connectors (1).
• Pull out the front accessory socket from the
socket cover (3).
810RW004
Installation
To install, follow the removal steps in the reverse or der.
