SECTION 12M2 - SEAT BELT SYSTEM
Service Precaution 
Seat Belt 
Front Seat Belt and Associated Parts
(Long Wheel Base) 
Removal 
Inspection
Installation 
Rear Seat Belt and Associated Parts
 
Removal 
Inspection
Installation 
Third Seat Belt and Associated Parts
 
Removal 
Inspection
Installation
Front Seat Buckle Assembly
 
Removal
 
Installation
 
Front Seat Buckle Assembly (W/Pretensioner)
Removal 
Installation 
Rear Center Seat Belt Buckle Assembly 
Rear Center Seat Belt Buckle Assembly
and Associated Parts 
Removal
Installation
Third Seat Belt Buckle and Lock Assembly 
Third Seat Belt Buckle and Lock Assembly
and Associated Parts 
Removal 
Installation
Rear Seat Lock Assembly 
Removal
Installation 
Rear Seat Lock Assembly (Bench Type) 
Removal 
Installation 
Rear Seat Strikers
Removal 
Installation 
Third Seat Striker 
Removal 
Installation 
Main Data and Specifications
Service Precaution
WARNING:  THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING, REFER TO
THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION:  Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
HOLDEN will call out those fasteners that require a
replacement after removal. HOLDEN will also call out
the fasteners that require thread lockers or thread
sealant. UNLESS OTHERWISE SPECIFIED, do not
use supplemental coatings (Paints, greases, or other
corrosion inhibitors) on threaded fasteners or
fasteners joint interfaces. Generally, such coatings
adversely affect the fastener torque and the joint
clamping force, and may damage the fasteners.
When you install fasteners, use the correct tightening
sequence and specifications. Following these
instructions can help you avoid damage to parts and
systems.

Legend

(1)Center Pillar Upper Trim Cover

(2)Adjust Shoulder Anchor Assembly/Seat Belt

Anchor Plate

(3)Center Pillar

(4)Dust Cover

(5)Retractor

(6)Anchor Bolt (Lower)

(7)Door Sill Plate (Front & Rear)

(8)Center Pillar Lower Trim Cover

(9)Front Seat Belt Assembly

(10)Front Seat Belt Anchor Bolt Cover and Anchor

Bolt

Seat Belt

Front Seat Belt and Associated Parts

760RW022

Removal

1.Disconnect the battery ground cable.

2.Remove the door sill plate (Front & Rear).

3.Remove the center pillar lower trim cover.

4.Remove the front seat belt anchor bolt cover and

anchor bolt (Upper Side).

●Refer to Center Pillar and Roof Side Trim Cover in

Exterior/Interior Trim section.

5.Remove the seat belt lower anchor bolt and screw,

and then remove the front seat belt.

6.Remove the adjust shoulder anchor assembly/seat

belt anchor plate.

●Refer to Center Pillar and Roof Side Trim Cover in

Exterior/Interior Trim section.

Inspection

If any of the following abnormalities is found, replace on

an assembly basis;

●Deform and malfunction of adjustable shoulder

anchor/seat belt anchor plate.

●No smooth move of upper/lower anchors in the

circumferential direction.

●Damaged and/or deformed through ring.

●Damaged and/or deformed tongue.

●Damaged and/or frayed of webbing.

●Deformed retractor bracket.

●Seat belt not rewound up.

●Resistance or abnormal sound when seat belt is

wound out and rewound.

●Retractor abnormality.

Inspection of retractor

1.ELR (Emergency Locking Retractor) lock inclining

angle check.

●When the retractor is moved gently from its installing

position, make sure it is not locked within 15°in any

directions, and it remains locked at 45°or larger.

2.ELR lock check.

●When the seat belt is drawn slowly with the retractor

installed, make sure it is not locked. And when it is

drawn quickly, make sure it is locked.

3.ALR (Automatic Locking Retractor)/ELR check

(Except for driver’s seat).

●When rewound after winding out the seat belt, make

sure the seat belt cannot be taken out. After

rewinding, make sure it has returned to its normal

operation.

CAUTION: Do not disassemble the retractor.

Installation

To install, follow the removal steps in the reverse order,

noting the following points;

1. Pass the seat belt through the lower trim cover hole,

and tighten the seat belt anchor bolts to the specified

torque.

Torque: 39 N·m (4.0 kg·m/29 lb ft)

2. After installing the trim cover to the body panel

securely, close the lower trim cover.

760RS006

Legend

(1)Rear Seat Belt Anchor Bolt Cover and Anchor

Bolt (Upper Side)

(2)Quarter Upper Trim Cover

(3)Rear Seat Belt Assembly

(4)Dust Cover

(5)Retractor

(6)Anchor Bolt (Lower Side)

(7)Luggage Side Trim Cover

(8)Rear End Floor Trim Cover

Rear Seat Belt and Associated Parts

Removal

1.Disconnect the battery ground cable.

2.Remove the rear end floor trim cover.

3.Remove the luggage side trim cover.

●Refer to Luggage Side and Quarter Upper Trim

Panel removal steps in Exterior/Interior Trim

section.

4.Remove the rear seat belt anchor bolt cover and

anchor bolt (Upper Side).

5.Remove the seat belt lower anchor bolt and remove

the retractor from dust cover slit to remove the rear

seat belt.

Inspection

If any of the following abnormalities is found, replace on

an assembly basis;

●No smooth move of upper/lower anchors in the

circumferential direction.

●Damaged and/or deformed through ring.

●Damaged and/or deformed tongue.

●Damaged and/or frayed of webbing.

●Deformed retractor bracket.

●Seat belt not rewound up.

●Resistance or abnormal sound when seat belt is

wound out and rewound.

●Retractor abnormality.

Inspection of retractor

1.ELR (Emergency Locking Retractor) lock inclining

angle check.

●When the retractor is moved gently from its installing

position, make sure it is not locked within 15°in any

directions, and it remains locked at 45°or larger.

2.ELR lock check.

●When the seat belt is drawn slowly with the retractor

installed, make sure it is not locked. And when it is

drawn quickly, make sure it is locked.

3.ALR (Automatic Locking Retractor)/ELR check

(Except for driver’s seat).

●When rewound after winding out the seat belt, make

sure the seat belt cannot be taken out. After

rewinding, make sure it has returned to its normal

operation.

CAUTION: Do not disassemble the retractor.

Installation

To install, follow the removal steps in the reverse order,

noting the following point.

1. Tighten the seat belt anchor bolts to the specified

torque.

Torque: 39 N·m (4.0 kg·m/29 lb ft)

Third Seat Belt and Associated Parts (Long Wheel Base)

760RW027

Legend

(1)Third Seat Belt Upper Anchor Bolt Cover and

Anchor Bolt

(2)Third Seat Belt Assembly

(3)Dust Cover

(4)Retractor

(5)Luggage Side Trim Cover

(6)Third Seat Belt Lower Anchor Bolt Cover and

Anchor Bolt

(7)Rear End Floor Trim Cover

Removal

1.Disconnect the battery ground cable.

2.Remove the rear end floor trim cover.

3.Remove the luggage side trim cover.

●Refer to Luggage Side and Quarter Upper Trim

Panel removal steps in Exterior/Interior Trim

section.

4. Remove the third seat belt anchor bolt cover and

anchor bolt (Upper Side).

5. Remove the seat belt lower anchor bolt and remove

the retractor from dust cover slit to remove the third

seat belt.

755RW043

Inspection

If any of the following abnormalities is found, replace on

an assembly basis;

●No smooth move of upper/lower anchors in the

circumferential direction.

●Damaged and/or deformed through ring.

●Damaged and/or deformed tongue.

●Damaged and/or frayed of webbing.

●Deformed retractor bracket.

●Seat belt not rewound up.

●Resistance or abnormal sound when seat belt is

wound out and rewound.

●Retractor abnormality.

Inspection of retractor

1.ELR (Emergency Locking Retractor) lock inclining

angle check.

●When the retractor is moved gently from its installing

position, make sure it is not locked within 15°in any

directions, and it remains locked at 45°or larger.

2.ELR lock check.

●When the seat belt is drawn slowly with the retractor

installed, make sure it is not locked. And when it is

drawn quickly, make sure it is locked.

CAUTION: Do not disassemble the retractor.

Installation

To install, follow the removal steps in the reverse order,

noting the following point.

1. Be sure to install the lower side anchor plate (1)

straight against the longitudinal direction of the

vehicle with mounting hole of the plate at the center.

2. Tighten the seat belt anchor bolts to the specified

torque.

Torque: 39 N·m (4.0 kg·m/29 lb ft)

Front Seat Buckle Assembly

Removal

1.Disconnect the battery ground cable.

2.Disconnect the seat belt warning connector (If so

equipped).

3.Remove the front seat buckle assembly(1).

Installation

To install, follow the removal steps in the reverse order,

noting the following points.

1.Fix the buckle to the rotation – stop position(2)

securely to install the front seat buckle assembly(1).

2.Tighten the buckle anchor bolt to the specified torque.

Torque: 39 N·m (4.0 kg·m/29 lb ft)

760RW023

760RS005

Front Seat Buckle Assembly (W/Pretensioner)

Removal

1.Disconnect the battery ground cable.

2.Disconnect the pretensioner harness connector(3).

3.Remove the pretensioner cover(1).

4.Remove the front seat buckle assembly(2).

Installation

To install, follow the removal steps in the reverse order,

noting the following points.

1. Fix the buckle to the rotation – stop position securely

to install the front seat buckle assembly.

2. Connect the pretensioner harness connector.

3. Tighten the buckle anchor bolt to the specified torque.

Torque: 39 N·m (4.0 kg·m/29 lb ft)

760RW030 760RW029

Rear Center Seat Belt Buckle Assembly

Rear Center Seat Belt Buckle Assembly and Associated Parts

1 4

760RW026

Legend

(1)Long Wheel Base

(2)Rear Seat Belt Buckle Assembly

(3)Seat Lock Cover

(4)Short Wheel Base

Removal

1.Remove the catch portions(2) & (3) of the seat lock

assembly(4) from the cover, and then remove the seat

lock cover(1).

2.Remove the rear seat buckle assembly.

Installation

1.Fix the rear seat belt buckle assembly(1) to the

rotation stopper and tighten the anchor bolt to the

specified torque.

Torque: 39 N·m (4.0 kg·m/29 lb ft)

2. Install the seat lock cover.

760RW016

760RW013

Third Seat Belt Buckle and Lock Assembly

Third Seat Belt Buckle and Lock

Assembly and Associated Parts Removal

1. Disconnect the battery ground cable.

2. Remove seat lock cover.

3. Remove third seat belt buckle assembly.

4. Remove third seat lock assembly.

Installation

To install, follow the removal steps in the reverse order,

noting the following point.

1. Tighten the lock assembly fixing bolts to the specified

torque.

Torque: 39 N·m (4.0 kg·m/29 lb ft)

2. Tighten the buckle assembly fixing bolt to the

specified torque.

Torque: 39 N·m (4.0 kg·m/29 lb ft)

755RW042

Legend

(1) Third Seat Belt Buckle Assembly

(2) Third Seat Lock Assembly

(3) Third Seat

(4) Seat Lock Cover

Rear Seat Lock Assembly

Removal

1.Remove the seat lock cover(3).

2.Remove the rear seat belt buckle assembly(1).

3.Remove the rear seat lock assembly(2).

Installation

To install, follow the removal steps in the reverse order,

noting the following point.

1.Tighten the seat lock fixing bolts to the specified

torque.

Torque: 42 N·m (4.3 kg·m/31 lb ft)

L.W.B

S.W.B

755RW040

Rear Seat Lock Assembly

(Bench Type)

Removal

1.Remove the seat lock cover(3).

2.Remove the rear seat belt/buckle assembly(1).

3.Disconnect the link connecting the lock assemblies on

the both sides, and then remove the rear seat lock

assembly(2).

Installation

To install, follow the removal steps in the reverse order,

noting the following point.

1. Tighten the seat lock fixing bolts to the specified

torque.

Torque: 42 N·m (4.3 kg·m/31 lb ft)

760RW003

Rear Seat Strikers

Removal

1.Fold the rear seat assembly to the front direction.

2.Remove the luggage floor box(1) (L·W·B).

Remove the striker cover(3) (S·W·B).

3.Remove the rear seat striker(2).

Installation

To install, follow the removal steps in the reverse order,

noting the following point.

1.Tighten the striker fixing bolts to the specified torque.

Torque: 40 N·m (4.1 kg·m/30 lb ft)

L.W.B

S.W.B

755RW045

Removal

1.Disconnect the battery ground cable.

2.Remove the striker cover (1).

3.Remove the third seat striker (2).

Installation

To install, follow the removal steps in the reverse order,

noting the following point.

1.Tighten the striker fixing nuts to the specified torque.

Torque: 39 N·m (4.0 kg·m/29 lb ft)

Third Seat Striker

755RW041

Front Seat Belt Anchor Bolts

Rear Seat Belt Anchor Bolts

Front Seat Buckle Anchor Bolt

Rear Seat Buckle Anchor Bolt

Rear Seat Lock Fixing Bolts

Third Seat Belt Anchor Bolts

Third Seat Lock Fixing Bolts

Third Seat Buckle Anchor Bolt

Third Seat Striker Fixing Nuts

Rear Seat Striker Fixing Bolts

Main Data and Specifications

Torque Specifications

Application N·m kg·m Lb Ft

4.0

4.3

4.0

4.1