holden.wiki

• MODEL SELECTION INDEX
• MY2005 VZ Series - Service Information
• Section 4A1Rear Suspension
  • 1 General Information
    • 1.1 VZ Models Except AWD
    • 1.2 AWD Wagon Models
      • Automatic Level Ride Suspension General Information
      • Automatic Level Ride Suspension Operation
        • Activation
        • Loaded Vehicle
        • Unloaded Vehicle
        • Deactivation
        • Reset Procedure
  • 2 Service Maintenance Operations
    • 2.1 Automatic Level Ride Suspension
      • Air Lines
      • Wiring Harness
      • Air Filter
  • 3 Service Operations
    • 3.1 Service Warnings, Cautions and Notes
    • 3.2 Rear Suspension Control Arm
      • Remove
      • Rear Suspension Control Arm Pivot Bushing, Replace
      • Reinstall
    • 3.3 Outer Rear Wheel Drive Shaft, Flange or Bearing (All VZ IRS Except AWD Wagon)
      • Replace
    • 3.4 Outer Rear Wheel Drive Shaft, Flange or Bearing (AWD Wagon Only)
      • Remove
      • Reinstall
    • 3.5 Rear Suspension Crossmember
      • Remove
        • For All VZ With IRS Except for AWD Wagon
        • For AWD Wagon
        • For All VZ With IRS Except for AWD Wagon
        • For AWD Wagon
      • Reinstall
    • 3.6 Rear Suspension Crossmember Front Mount Bushing
      • Off-Car Replacement
      • On-Car Replacement
    • 3.7 Rear Suspension Crossmember Mass Damper
      • Remove
      • Reinstall
    • 3.8 Rear Suspension Crossmember Rear Mount
      • Remove
      • Reinstall
    • 3.9 Stabiliser Bar and/or Mountings
      • Remove
      • Stabiliser Bar Link Insulators, Replace
      • Reinstall
    • 3.10 Rear Spring and Insulators
      • Remove
      • Reinstall
    • 3.11 Rear Shock Absorbers and/or Bushing
      • Remove
        • For MY 2005 VZ Series Sedan and Coupe Models
        • For MY 2005 VZ Series Wagon and Utility Models
      • Lower Bushing, Replace
      • Reinstall
        • For MY 2005 VZ Series Sedan and Coupe Models
        • For MY 2005 VZ Series Wagon and Utility Models
        • For all MY 2005 VZ Series Models
    • 3.12 Additional Control Arm
      • Inspect
      • Remove
      • Disassemble
      • Reassemble
      • Reinstall
    • 3.13 Rear Wheel Alignment Checking
      • Camber and Toe Check
        • Preliminary Checks and Information
      • Rear Wheel Toe Adjustment
  • 4 Service Operations – Automatic Level Ride Suspension
    • 4.1 Initial Air Charge
    • 4.2 Air Leak Test
    • 4.3 Relieving System Air Pressure
    • 4.4 Compressor Assembly
      • Remove
      • Disassemble
      • Reassemble
      • Reinstall
    • 4.5 Air Lines
      • Remove
      • Reinstall
    • 4.6 Automatic Level Ride Shock Absorber
      • Remove
      • Reinstall
    • 4.7 Ride Height Sensor
      • Remove
      • Reinstall
  • 5 Diagnosis
    • 5.1 Checking and Testing Shock Absorbers
      • Leakage Criteria
    • 5.2 Diagnosis – Automatic Level Ride Suspension
      • Equipment
      • Ride Height Sensor Reset
    • 5.3 Preliminary Diagnostic Procedure
    • 5.4 Compressor Assembly Test – Motor
    • 5.5 Compressor Assembly Test – Solenoid
    • 5.6 Ride Height Sensor Test – Compressor
    • 5.7 Ride Height Sensor Test – Solenoid
    • 5.8 Wiring Diagram – Automatic Level Ride Suspension
    • 5.9 Wiring Harness Layout – Automatic Level Ride Suspension
  • 6 Specifications
    • Rear Suspension Service Alignment Data
    • Rear Spring Details
    • Rear Shock Absorber Details
    • Rear Stabiliser Bar Details
  • 7 Torque Wrench Specifications
  • 8 Special Tools