holden.wiki

• MODEL SELECTION INDEX
• MY2006 VZ Series - Service Information
• Section 6C1-3 Engine Management – V6 Service Operations
  • 1 General Information
    • 1.1 General Description
    • 1.2 Service Precautions and Requirements
      • Service Precautions
      • Service Requirements
        • Basic Knowledge Required
        • Basic Diagnostic Tools Required
    • 1.3 Service Operations Not Covered In This Section
      • Air-conditioning System
      • Electrical Components
      • Engine Dress Covers
      • Fuel System
      • Transmission – Automatic
      • Transmission – Manual
  • 2 Component Replacement
    • 2.1 Accelerator Pedal Position Sensor
      • Remove
      • Reinstall
    • 2.2 Accelerator Pedal Position Sensor Support Bracket
      • Remove
      • Reinstall
    • 2.3 Air Cleaner Assembly
      • Air Cleaner Upper Housing
        • Remove
        • Reinstall
      • Air Cleaner Lower Housing Assembly
        • Remove
        • Reinstall
    • 2.4 Barometric Pressure Sensor
      • Remove
      • Reinstall
    • 2.5 Camshaft Position Actuator Solenoid
      • Bank 1 (RHS)
        • Remove
        • Reinstall
      • Bank 2 (LHS)
        • Remove
        • Reinstall
      • Test
        • Resistance Inspection
        • Functional Test
    • 2.6 Camshaft Position Sensor
      • Bank 1 (RHS)
        • Remove
        • Reinstall
      • Bank 2 (LHS)
        • Remove
        • Reinstall
    • 2.7 Crankshaft Position Sensor
      • Remove
      • Test
        • Resistance Check
      • Reinstall
    • 2.8 Engine Coolant Temperature Sensor
      • Remove
      • Test
        • Resistance Check
      • Reinstall
    • 2.9 Engine Control Module
      • Remove
      • Reinstall
      • ECM Reset
    • 2.10 Engine Control Module Bracket Assembly
      • Remove
      • Reinstall
    • 2.11 Engine Oil Level and Temperature Sensor
      • Remove
      • Test
        • Engine Oil Level Sensor Check
      • Reinstall
    • 2.12 Engine Oil Pressure Sensor
      • Remove
      • Reinstall
    • 2.13 Evaporative Emission (EVAP) Canister Purge Valve Quick Connect Fittings
      • Disconnect
        • Locking Lever Type
        • Latch Type
        • Connect
    • 2.14 Evaporative Emission Canister Purge Valve
      • Remove
      • Test
        • Resistance Check
        • Functional Test
      • Reinstall
    • 2.15 Fuel Rail Assembly
      • Remove
      • Disassemble
        • Fuel Injector
        • Fuel Injector Wiring Harness Assembly
      • Reinstall
    • 2.16 Heated Oxygen Sensor
      • Service Precautions
      • Six Wire Sensor
        • Remove
        • Reinstall
      • Four Wire Sensor
        • Remove
        • Reinstall
      • Test
        • Heater Resistance Check – Six Wire HO2S
        • Heater Resistance Check – Four Wire HO2S
    • 2.17 Ignition Coil
      • Ignition Coils
        • Remove
        • Disassemble
        • Reassemble
        • Test
        • Reinstall
    • 2.18 Intake Air Duct Assembly
      • Remove
      • Reinstall
    • 2.19 Intake Air Temperature Sensor
      • Test
        • Resistance Check
    • 2.20 Intake Manifold Runner Control (IMRC) Solenoid Valve - Alloytec High Output Engine
      • Remove
      • Test
        • Resistance Check
        • Functional Test
      • Reinstall
    • 2.21 Knock Sensor, Bank 2 (LHS)
      • Remove
      • Reinstall
    • 2.22 Knock Sensor, Bank 1 (RHS)
      • Remove
      • Reinstall
    • 2.23 Mass Air Flow Sensor
      • Handling Precautions
      • Remove
      • Reinstall
    • 2.24 Schrader Valve – Fuel Pressure Gauge Connection Point
      • Remove
      • Reinstall
    • 2.25 Spark Plugs
      • Service Precautions
      • Remove
      • Inspect
      • Spark Plug Inspection
        • Poor Spark Plug Performance
        • Analysis of Spark Plug Condition
      • Reinstall
    • 2.26 Throttle Body Assembly
      • Handling Precautions
      • Remove
      • Inspect
      • Reinstall
  • 3 Specifications
  • 4 Assembly Lubricants
  • 5 Torque Specifications
  • 6 Special Tools