holden.wiki

• MODEL SELECTION INDEX
• MY 2005 VZ Series - Service Information
• Section 7C4 Automatic Transmission – 4L60E – On-Vehicle Ser
  • 1 General Information
    • 1.1 General Service Information
      • Description
      • Service Information
  • 2 Maintenance Operations
    • 2.1 Transmission Fluid
      • Transmission Fluid Level
      • Transmission Fluid Colour
    • 2.2 Reverse Flush and Flow Rate Test
      • Reverse Flush
      • Flow Rate Test
  • 3 Service Operations
    • 3.1 Fluid Change and Filter Replacement
      • Remove
      • Reinstall
    • 3.2 Selector Linkage and Rod, Except AWD
      • Remove
      • Inspect
      • Reinstall
    • 3.3 Selector Cable Assembly, AWD
      • Remove
      • Reinstall
    • 3.4 Shift Selector Assembly, Except AWD
      • Remove
      • Disassemble
        • Lower Housing Assembly
        • Patch Harness and Switch
        • Upper Cover, Boot and Selector Knob
        • Selector Lever Assembly
      • Reinstall
    • 3.5 Shift Selector Assembly, AWD
      • Remove
      • Disassemble
        • Lower Housing Assembly
        • Patch Harness and Switch
        • Upper Cover, Boot and Selector Knob
      • Reinstall
    • 3.6 Neutral Start and Back-up Lamp Switch, Except AWD
      • Remove
      • Reinstall
      • Adjust
    • 3.7 Neutral Start and Back-up Lamp Switch, AWD
      • Remove
      • Reinstall
      • Adjust
    • 3.8 Vehicle Speed Sensor, Except AWD
      • Remove
      • Reinstall
    • 3.9 Vehicle Speed Sensor, AWD
      • Remove
      • Reinstall
    • 3.10 Manual Shaft Oil Seal
      • Replace
    • 3.11 Transmission Support and Mount, Except AWD
      • Remove
      • Reinstall
    • 3.12 Extension Housing and Rear Bush, Except AWD
      • Remove
      • Reinstall
    • 3.13 Extension Housing Oil Seal, Except AWD
      • Replace
    • 3.14 Transmission Support and Adaptor Housing, AWD
      • Remove and Reinstall
    • 3.15 Shift Solenoid Locations
      • Location and Identification
    • 3.16 1 – 2 Accumulator Assembly
      • Remove
      • Clean and Inspect
      • Reinstall
    • 3.17 Control Valve Body Harness
      • Remove
      • Reinstall
    • 3.18 Control Valve Body
      • Remove
      • Disassemble, Clean, Inspect and Reassemble
      • Reinstall
    • 3.19 Spacer Plate, Check Balls, Filter Screens and 3 – 4 Accumulator
      • Remove
      • Clean and Inspect
      • Reinstall
    • 3.20 Filler Tube and Breather Hose
      • Remove
        • V6 Engine
        • GEN III V8 Engine
      • Reinstall
    • 3.21 Transmission Cooler Lines and Hoses
      • Arrangement
        • Radiator
        • V6 Engine – Fluid Cooler Lines, Except AWD
        • V6 Engine – Fluid Cooler Lines, AWD
        • GEN III V8 Engine – Fluid Cooler Lines
      • Radiator Cooler Hoses / Lines
        • Remove
        • Reinstall
      • Transmission Fluid Lines
        • V6 Engine
        • GEN III V8 Engine
    • 3.22 Transmission Assembly – V6, Except AWD
      • Remove
      • Reinstall
    • 3.23 Transmission Assembly – GEN III V8, Except AWD
      • Remove
      • Reinstall
    • 3.24 Transmission Assembly, V6 AWD
      • Remove
      • Reinstall
    • 3.25 Transmission Assembly, GEN III V8 AWD
      • Remove
      • Reinstall
    • 3.26 Transmission Control Module
      • Remove
      • Reinstall
      • TCM Programming Procedure
  • 4 Specifications
  • 5 Torque Wrench Specifications
  • 6 Special Tools