Exterior Ornamentation Page 1A9–1

Page 1A9–1

Section 1A9

Exterior Ornamentation

ATTENTION

Before performing any service operation or other procedure described in this Section, refer to Section 00

Warnings, Cautions and Notes for correct w orkshop practices wi th regard to safety and/or property damage.

1 General Information...............................................................................................................................2

1.1 Pictorial Index ........................................................................................................................................................ 2

Statesman............................................................................................................................................................... 3

Caprice.................................................................................................................................................................... 4

2 Service Operations.................................................................................................................................5

2.1 Hood Emblem......................................................................................................................................................... 5

Remove................................................................................................................................................................... 5

Reinstall.................................................................................................................................................................. 5

2.2 Fender Name Plate................................................................................................................................................. 6

Remove................................................................................................................................................................... 6

Reinstall.................................................................................................................................................................. 6

2.3 Rear Compartment Lid Emblem ........................................................................................................................... 7

Remove................................................................................................................................................................... 7

Reinstall.................................................................................................................................................................. 7

2.4 Rear Compartment Lid Moulding Assembly........................................................................................................ 8

Remove................................................................................................................................................................... 8

Reinstall.................................................................................................................................................................. 8

2.5 Roof Joint Moulding.............................................................................................................................................. 9

Remove................................................................................................................................................................... 9

Reinstall.................................................................................................................................................................. 9

2.6 Door Opening Moulding...................................................................................................................................... 10

Remove................................................................................................................................................................. 10

Reinstall................................................................................................................................................................ 10

2.7 Body Side Mouldings .......................................................................................................................................... 11

Remove................................................................................................................................................................. 11

Reinstall................................................................................................................................................................ 11

2.8 Rocker Panel Moulding Assembly...................................................................................................................... 13

Remove................................................................................................................................................................. 13

Reinstall................................................................................................................................................................ 14

2.9 Centre Pillar Upper Finisher Assembly.............................................................................................................. 15

Remove................................................................................................................................................................. 15

Reinstall................................................................................................................................................................ 15

3 Torque Wrench Specifications ...........................................................................................................16

Exterior Ornamentation Page 1A9–2

Page 1A9–2

1 General Information

This Section describes the service procedures for the external ornamentation components such as emblems, name

plates, mouldings and finishers.

Many of the components are affixed to the

vehicle with double-sided tape or urethane

adhesive. It is imperative the correct

materials, as specified in this Section, are

used when reassembling these parts. Use of

materials other than those specified may lead

to premature failure.

To aid in identification and service procedure location, refer to the pictorial index diagrams on the following pages.

1.1 Pictorial Index

The following diagrams provide a quick reference to the correct service procedures for exterior ornamentation

components.

Simply locate the component in the correct figure below and using the reference chart, go to the appropriate service

procedure.

Model Refer To Model Refer To

Statesman Figure 1A9 – 1 Caprice Figure 1A9 – 2

Exterior Ornamentation Page 1A9–3

Page 1A9–3

Statesman

Figure 1A9 – 1

Reference Chart: Statesman

Item Description Refer to

1 Hood Emblem: Holden 2.1 Hood Emblem

2 Fender Name Plate: Alloytec190, V8 2.2 Fender Name Plate

3 Rear Compartment Lid Emblem: Holden 2.3 Rear Compartment Lid Emblem

4 Rear Compartment Lid Moulding Assembly:

Statesman 2.4 Rear Compartment Lid Moulding Assembly

5 Roof Joint Moulding 2.5 Roof Joint Moulding

6 Door Opening Moulding 2.6 Door Opening Moulding

7 Body Side Moulding 2.7 Body Side Mouldings

8 Rocker Panel Moulding Assembly 2.8 Rocker Panel Moulding Assembly

9 Centre Pillar Upper Finisher Assembly 2.9 Centre Pillar Upper Finisher Assembly

Exterior Ornamentation Page 1A9–4

Page 1A9–4

Caprice

Figure 1A9 – 2

Reference Chart: Caprice

Item Description Refer to

1 Hood Emblem: Holden 2.1 Hood Emblem

2 Fender Name Plate: Alloytec190, V8 2.2 Fender Name Plate

3 Rear Compartment Lid Emblem: Holden 2.3 Rear Compartment Lid Emblem

4 Rear Compartment Lid Moulding Assembly: Caprice 2.4 Rear Compartment Lid Moulding Assembly

5 Roof Joint Moulding 2.5 Roof Joint Moulding

6 Door Opening Moulding 2.6 Door Opening Moulding

7 Body Side Moulding 2.7 Body Side Mouldings

8 Rocker Panel Moulding Assembly 2.8 Rocker Panel Moulding Assembly

9 Centre Pillar Upper Finisher Assembly 2.9 Centre Pillar Upper Finisher Assembly

Exterior Ornamentation Page 1A9–5

Page 1A9–5

2 Service Operations

2.1 Hood Emblem

LT Section No. — 10–150

Remove

1 Protect the paint and bodywork with tape or a clean

rag.

2 To assist removal, warm the emblem with a heat-lamp

or heat-gun to soften the adhesive.

NOTE

The emblem has three locating lugs that must

not be cut if the emblem is to be reused.

3 Using a knife or paint scraper, carefully remove the

emblem assembly from the hood, cutting the double-

sided tape.

4 As required remove any remaining double-sided tape

from the emblem and/or hood and clean the surfaces

with Prepsol or equivalent. Figure 1A9 – 3

Reinstall

NOTE

If the hood has been replaced, the new part will

require drilling with emblem holes, refer to

Section 1A4 Hood and Rear Compartment Lid.

1 If reusing the emblem, apply new polyethylene double-sided tape such as 3M 4428 or equivalent to the back of the

name plate. Trim back the tape slightly away from the edge of the emblem.

2 Clean the surface of the hood with Prepsol or equivalent.

3 Remove the backing paper from the double-sided tape.

4 Align the emblem. Locate the lugs with their

corresponding holes at the centre line of the hood.

5 Affix the emblem and press firmly over the entire

emblem for at least 10 seconds to ensure sound

adhesion.

Figure 1A9 – 4

Exterior Ornamentation Page 1A9–6

Page 1A9–6

2.2 Fender Name Plate

LT Section No. — 10–150

Remove

1 Protect the paint and body side moulding with tape or

a clean rag.

2 To assist removal, warm the name plate with a heat-

lamp or heat-gun to soften the adhesive.

3 Using a paint scraper or similar, carefully prise the

name plate from the body side moulding.

4 As required remove any remaining double-sided tape

from the name plate and/or body side moulding and

clean the surfaces with Prepsol or equivalent.

Figure 1A9 – 5

Reinstall

1 If reusing the name plate, apply new polyethylene double-sided tape such as 3M 4428 or equivalent to the back of

the name plate. Trim back the tape slightly away from the edge of the name plate.

2 Clean the body side moulding surface with Prepsol or equivalent.

3 Remove the backing paper from the double-sided tape.

4 Apply the name plate in the position shown, refer to Figure 1A9 – 6. Ensure it is positioned parallel to the moulding.

Figure 1A9 – 6

5 Press firmly over the entire name plate for at least 10 seconds to ensure sound adhesion.

Exterior Ornamentation Page 1A9–7

Page 1A9–7

2.3 Rear Compartment Lid Emblem

LT Section No. — 10–150

Remove

1 Protect the paint and bodywork with tape or a clean

rag.

2 To assist removal, warm the emblem with a heat-lamp

or heat-gun to soften the adhesive.

NOTE

The emblem has two locating lugs that must not

be cut if the emblem is to be reused.

3 Using a paint scraper or similar, carefully prise the

emblem from the rear compartment lid.

4 As required, remove any remaining double-sided tape

from the emblem and/or rear compartment lid and

clean the surfaces with Prepsol or equivalent.

Figure 1A9 – 7

Reinstall

1 If reusing the emblem, apply new polyethylene double-sided tape such as 3M 4428 or equivalent to the back of the

emblem. Trim back the tape slightly away from the edge of the emblem.

2 Clean the panel surface with Prepsol or equivalent.

3 Remove the backing paper from the double-sided tape.

4 Apply the emblem in the position shown, ensuring the

locating pins are correctly orientated with the locating

holes in the panel surface.

5 Press firmly over the entire emblem for at least 10

seconds to ensure sound adhesion.

Figure 1A9 – 8

Exterior Ornamentation Page 1A9–8

Page 1A9–8

2.4 Rear Compartment Lid Moulding

Assembly

LT Section No. — 10–150

Remove

1 Raise the rear compartment lid.

2 Remove the screw (1), two places, attaching the rear compartment lid moulding assembly (2), refer to

Figure 1A9 – 9.

3 Remove the spacers (3) that were separating the screws from the rear compartment lid sheet metal.

NOTE

Be careful not to damage the five retaining tabs

on the rear compartment lid moulding assembly if

the assembly is to be reused.

4 Beginning at each end and working towards the centre release the four outer tabs (4) by carefully manoeuvring

them down and out of the holes.

5 Release the centre tab (5) by carefully lifting and pulling the moulding assembly from the rear compartment lid.

Figure 1A9 – 9

Reinstall

Reinstallation of the rear compartment lid moulding assembly is the reverse of the removal procedure, noting the

following:

1 Align the tabs with their corresponding holes on the rear compartment lid.

2 Tighten the screws to the correct torque specification.

Rear compartment lid moulding assembly

attaching screw torque specification ...........1.4 – 1.8 Nm

Exterior Ornamentation Page 1A9–9

Page 1A9–9

2.5 Roof Joint Moulding

LT Section No. — 10–150

Remove

Take care as the retaining clips can easily

break. Protect the paintwork with a clean rag.

1 Beginning at the front of the vehicle, use a screwdriver

to carefully prise the roof joint moulding (1) from the

roof channel, disengaging the retaining clips (2), five

places and remove.

Figure 1A9 – 10

Reinstall

1 As required, seat the five retainers onto the roof joint moulding, spacing them evenly.

2 Seat the roof joint moulding in the roof channel and beginning at the rear, clip it in place.

3 At the front, ensure the moulding is installed under the windshield moulding cover.

Exterior Ornamentation Page 1A9–10

Page 1A9–10

2.6 Door Opening Moulding

LT Section No. — 10–150

Remove

1 Open the front and rear doors on the relevant side of

the vehicle.

2 Beginning at each end and working towards the

middle, remove the screw (1), 10 places, attaching the

door opening moulding (2) to the vehicle.

3 Carefully remove the moulding.

Figure 1A9 – 11

Reinstall

Reinstallation of the door opening moulding is the reverse of the removal procedure. Tighten the screws to the correct

torque specification.

Door opening moulding attaching

screw torque specification...........................1.0 – 2.0 Nm

NOTE

The screws are encapsulated with a wax sealer. It

is recommended the screws be replaced once

removed, however if this is impractical, apply a

small amount of sealer to the end of the thread.

Exterior Ornamentation Page 1A9–11

Page 1A9–11

2.7 Body Side Mouldings

LT Section No. — 10–150

Remove

1 Protect the paint and bodywork with tape or a clean

rag.

2 Using a paint scraper or similar, begin at one end and

carefully prise the moulding from the panel, cutting

through the double-sided tape and urethane adhesive.

NOTE

As an alternative, carefully use a length of piano

wire to cut the adhesive in a similar way to

removing a windshield. If required, refer to

Section 1A6 Stationary Windows.

3 As required, remove any remaining double-sided tape

and adhesive from the moulding and/or panel.

Figure 1A9 – 12

Reinstall

1 Clean the surfaces with Prepsol or equivalent.

2 Place a mark on the rear edge of the fender and/or door panels at the three points shown as required. Measure in a

straight line from the lower edge of each panel, refer to Figure 1A9 – 13.

3 If a complete moulding set is to be fitted, or as required, apply a length of masking tape along the side of the

vehicle, aligning the top edge of the tape with the marks. Begin by affixing the tape at the rear of the rear door, hold

it taut and away from the vehicle, and affix it to each panel. Ensure it is straight and then smooth it down along its

length.

4 If reusing the moulding, apply new acrylic double-sided tape (1) such as 3M 5344 or equivalent along the back of

the moulding.

5 Apply a 3.0mm diameter bead of urethane adhesive such as Expandite Betaseal 554.02, Sikaflex Drive or

equivalent over the entire length of moulding (2).

NOTE

Refer to any further directions supplied with the

urethane adhesive.

6 Affix the moulding to the vehicle in the correct positions, aligning the lower edge with the masking tape (if fitted)

and:

• For the fender moulding begin at the rear edge of the fender, aligning to the dimension at Section B–B.

• For the front door moulding begin at the front edge of the front door, aligning to the dimension at Section

B–B.

• For the rear door moulding begin at the front edge of the rear door, aligning to the dimension at Section C–C.

• For the rear quarter panel moulding begin at the rear quarter panel edge closest to the rear door aligning to

the dimension at Section D–D.

7 Press firmly over the length of the moulding(s) at the double-sided tape for 10 seconds to ensure sound adhesion.

Exterior Ornamentation Page 1A9–12

Page 1A9–12

Figure 1A9 – 13

Exterior Ornamentation Page 1A9–13

Page 1A9–13

2.8 Rocker Panel Moulding Assembly

LT Section No. — 10–150

Remove

1 On the relevant side remove the rear road wheel, refer

to Section 10 Wheels and Tyres.

2 Remove the screw (1), two places, attaching the rear

rocker panel moulding (3) and wheelhouse liner (2).

NOTE

If required, the rear rocker panel moulding can

be removed at this stage by sliding it rearward

from the front rocker panel moulding.

Figure 1A9 – 14

3 Remove the screw (1), two places, attaching the front

rocker panel moulding (2) to the fender and liner.

4 Lift up the rocker panel weatherstrip (1) to gain access

and remove the retainer (2), nine places, attaching the

front rocker panel moulding (3), refer to

Figure 1A9 – 16.

5 Remove the screw (4), seven places, from the

retainer (5) under the moulding.

6 Remove the moulding.

7 If required, prise the nut (6), two places, from the

fender.

Figure 1A9 – 15

Figure 1A9 – 16

Exterior Ornamentation Page 1A9–14

Page 1A9–14

8 If required, remove the retainer (1), seven places, by

gently levering out from the body, taking care not to

damage the paint work.

Figure 1A9 – 17

Reinstall

Reinstallation of the rocker panel moulding assembly is the reverse of the removal procedure, noting the following:

1 Tighten the screws to the correct torque specification.

Rocker panel moulding attaching

screw torque specification...........................1.0 – 3.0 Nm

2 Ensure the weatherstrip is seated correctly.

Exterior Ornamentation Page 1A9–15

Page 1A9–15

2.9 Centre Pillar Upper Finisher Assembly

LT Section No. — 10–250

Remove

1 Open the front and rear doors on the relevant side of

the vehicle.

2 Gently prise the top of the centre pillar upper finisher

(1) out to disengage it from the centre pillar upper

finisher retainer (2).

3 Holding the top of finisher out, slide it down the centre

pillar outer sealing strips (3) until it rests on rear door

hinge.

4 Manoeuvre the finisher from the sealing strips and

remove.

Figure 1A9 – 18

5 Remove the screw (1), seven places, securing the

centre pillar sealing strips (2) to the pillar and remove

the strips.

6 Partially remove the door opening moulding, refer to

2.6 Door Opening Moulding.

7 Remove centre pillar upper trim panel (3) by pulling

away from the pillar.

8 Remove the screw (4) attaching the centre pillar upper

finisher retainer (5) and centre pillar upper trim mount

plate (6) to the pillar and remove.

Figure 1A9 – 19

Reinstall

Reinstallation of the centre pillar upper finisher assembly is the reverse of the removal procedure, noting the following:

1 Ensure the centre pillar upper trim panel is seated correctly under the door opening weatherstrips.

2 Ensure the screws are tightened to the correct torque specification.

Centre pillar upper finisher retainer

attaching screw torque specification ...........1.0 – 3.0 Nm

Centre pillar sealing strip attaching

screw torque specification...........................1.0 – 3.0 Nm

Exterior Ornamentation Page 1A9–16

Page 1A9–16

3 Torque Wrench Specifications

Rear Compartment Lid Moulding Assembly

Attaching Screw...........................................................................1.4 – 1.8 Nm

Door Opening Moulding Attaching Screw....................................1.0 – 2.0 Nm

Rocker Panel Skirt Attaching Screw............................................ 1.0 – 3.0 Nm

Centre Pillar Upper Finisher Retainer Attaching Screw...............1.0 – 3.0 Nm

Centre Pillar Sealing Strip Attaching Screw.................................1.0 – 3.0 Nm