holden.wiki

• MODEL SELECTION INDEX
• MY 2006 WL Series - Service Information
• Section 4B1Rear Final Drive and Drive Shafts
  • 1 General Information
    • 1.1 General Description
    • 1.2 Final Drive Assembly Identification
      • Final Drive Application
    • 1.3 Final Drive Assembly Maintenance
      • Maintenance
        • Drive Shaft Bearings and Constant Velocity Joints
        • Differential Carrier Assembly
        • Final Drive Assembly Breather
      • Lubrication
  • 2 Minor Service Operations
    • 2.1 General Information
      • Important Service Requirements
    • 2.2 Checking Differential Carrier Lubricant Level
    • 2.3 Changing/Flushing Rear Axle Lubricant
    • 2.4 Trailing Arm Outer Rear Wheel Drive Shaft Assembly Hub
      • Check for Run-Out
      • If Run-out is Within Specification:
      • If the Run-out Check, Exceeds Specification:
    • 2.5 Trailing Arm Outer Rear Wheel Drive Shaft Assembly Hub S
      • Replace
    • 2.6 Drive Shaft Assembly
      • Remove
      • Reinstall
    • 2.7 Drive Shaft and/or Constant Velocity Joints
      • Disassemble
      • Inspect
        • Drive Shaft and Boots
        • Constant Velocity Joints
      • Reassemble
        • Constant Velocity Joints
        • Drive Shaft and Boots
    • 2.8 Inner Axle Shaft Seal
      • Replace
    • 2.9 Pinion Oil Seal
      • Replace
    • 2.10 Pinion Flange
      • Replace
        • Using Old Oil Seal
        • Replace (Using New Oil Seal)
  • 3 Major Service Operations
    • 3.1 Outer Rear Wheel Drive Shaft Flange Outer Rear Wheel Drive Shaft Assembly and/or Wheel Bearing
      • Remove
      • Reinstall
        • To Install a New Bearing:
        • To Reinstall Outer Rear Wheel Drive Shaft:
    • 3.2 Final Drive Assembly
      • Remove
      • Reinstall
    • 3.3 Removed Final Drive Assembly
      • Disassemble
        • Differential Case
      • Inspect
        • Differential Case
        • Differential Side Gears and Pinion Gears
        • Ring Gear and Pinion
        • Bearings
        • Differential Carrier
        • Screw Adjusters and Inner Axle Shafts
        • Rear Cover
      • Reassemble
        • Differential Case
        • Differential Case Side Bearing Pre-Load Setting
      • Hypoid Pinion Positioning Shim Selection
      • Pinion Installation
      • Differential Backlash Setting
      • Ring Gear and Pinion Contact Pattern
        • Tooth Marking Nomenclature
        • Ideal Contact
        • Acceptable Heel Contacts
        • Acceptable Toe Contacts
    • 3.4 Limited Slip Differential
      • Disassemble
      • Inspect
        • Differential Case
        • Differential Side Gears and Pinion Gears
        • Ring Gear and Pinion
        • Bearings
      • Reassemble
    • 3.5 Rear Axle
      • Reassemble
  • 4 Diagnosis
    • 4.1 General Information
      • Road Test
      • Tyre Noise
      • Front Wheel Bearings
      • Transmission Rear Bearing (Manual Transmission)
      • Backlash Clunk
      • Drive-Line Snap
      • Engine and Other Contributing Factors
    • 4.2 Final Drive Assembly Noise
      • Gear Related Noise
        • Ring Gear and Pinion Noise
        • Differential Side Gear and Pinion Noise
        • Common Causes of Gear Related Noises
      • Bearing Related Noise
        • Differential Pinion Gear Bearings
        • Outer Rear Wheel Drive Shaft Wheel Bearings
        • Differential Side Bearings
        • Common Causes of Bearing Related Noises
    • 4.3 Final Drive Bearing Diagnosis
  • 5 Specifications
  • 6 Torque Wrench Specifications
  • 7 Special Tools