SECTION 0C1 - SERVICE PROGRAMMING SYSTEM
Service Precaution
Service Programming System (SPS)
Service Precaution
WARNING: THIS VEHICLE HAS A SUPPLEMENTAL
RESTRAINT SYSTEM (SRS). REFER TO THE SRS
COMPONENT AND WIRING LOCATION VIEW IN
ORDER TO DETERMINE WHETHER YOU ARE
PERFORMING SERVICE ON OR NEAR THE SRS
COMPONENTS OR THE SRS WIRING. WHEN YOU
ARE PERFORMING SERVICE ON OR NEAR THE
SRS COMPONENTS OR THE SRS WIRING, REFER
TO THE SRS SERVICE INFORMATION. FAILURE TO
FOLLOW WARNINGS COULD RESULT IN POSSIBLE
AIR BAG DEPLOYMENT, PERSONAL INJURY, OR
OTHERWISE UNNEEDED SRS SYSTEM REPAIRS.
CAUTION: Always use the correct fastener in the
proper location. When you replace a fastener, use
ONLY the exact part number for that application.
HOLDEN will call out those fasteners that require a
replacement after removal. HOLDEN will also call
out the fasteners that require thread lockers or
thread sealant. UNLESS OTHERWISE SPECIFIED,
do not use supplemental coatings (Paints, greases,
or other corrosion inhibitors) on threaded fasteners
or fastener joint interfaces. Generally, such
coatings adversely affect the fastener torque and
the joint clamping force, and may damage the
fastener. When you install fasteners, use the correct
tightening sequence and specifications. Following
these instructions can help you avoid damage to
parts and systems.
Service Programming System (SPS)
The ECU fitted to MY2002 TF Rodeo vehicles with the 4JH1-TC Diesel engine uses a non removable EEPROM
(Flash Memory). The ECU is programmed from the factory with the proper calibrations for vehicle operation. In the
event that the ECU is replaced, or an updated calibration is required to correct a vehicle's operating condition, the
ECU will have to be programmed with the new calibration. Programming is accomplished through the vehicle DLC
using the TECH 2 Service Programming System (SPS) and TIS 2000.
A service replacement ECU may not be programmed. DTC P0601 - ECU Memory and DTC P0602 -ECU Not Pro-
grammed indicates the flash memory is not programmed or has malfunctioned. For further DTC information and diag-
nostic procedures refer to Section 6C1.
CAUTION:
1. Before performing SPS, inspect the TECH 2 DLC cable and the DLC connector and terminals for damage. Any
damage that causes an open circuit during the programming procedure may result in irreparable damage to the
ECU.
2. Battery voltage must be between 12 and 14 volts. The vehicle to be programmed must not be connected to a
battery charger during the programming procedure. Incorrect battery voltage may cause programming failure and/or
ECU failure.
3. Do Not alter the status of either the ignition switch or TECH 2 unless instructed to do so by the programming
procedure. Turning either the ignition switch or TECH 2 OFF during the SPS programming procedure may result in
irreparable damage to the ECU.
NOTE:
When installing a new ECU, ensure that the correct ECU is fitted to the vehicle. Refer to the latest parts listing for ECU
part number identification.
NOTE: Due to the constant evolution of TECH 2
software, the screens shown in this section may
differ slightly from those displayed for the vehicle
being tested.
1. Connect TECH 2 to DLC. Turn the ignition ON.
Press the TECH 2 PWR button to turn on TECH 2.
2. When the TECH 2 title screen is displayed, press
ENTER to continue.
3. Select F1: Service Programming System.
VX0C000
Press [ENTER] to continue.
Software Version 10.XXX
Holden 1997 - 2002
Tech
TFSPS000
10 Megabyte
Main Menu
TFSPS001
F0: Diagnostics
F1: Service Programming System (SPS)
F2: View Capture Data
F3: Tool Options
F4: Download/Upload Help
4. Select F0: Request Info and follow the instructions
on the screen.
5. If there is data already stored, TECH 2 will display
the stored data. If there is no data stored in TECH 2
then the Model Year selection screen will be dis-
played.
Press the Continue Soft Key to request new
information.
6. Select the correct Model Year for the vehicle with the
arrow keys and the press ENTER.
Service Programming System (SPS)
Version 4.132
Tech 2 is ready to request data from the
vehicle!
TFSPS002
F0: Request Info
Continue Keep Data
Service Programming System (SPS)
Version 4.132
Continue and request new info?
Data already stored in Tech 2!
VIN:
System:
Hardware:
Software:
JAATFS77H27103726
4JHI
97255155.2
BOS 01D001
TFSPS003
Main Menu
Select one of the following
Model Year(s)
TFSPS004
(2)
(1)
(Y)
(X)
(W)
(2)
2002
2001
2000
1999
1998
1 / 5
2002
7. the correct vehicle type with the arrow keys and then
press ENTER.
8. Turn off ignition! then press the Okay soft key to con-
tinue.
9. When Ignition Switched OFF! is displayed, press
the Okay soft key to continue.
Main Menu
Select one of the following
Vehicle Type(s)
Frontera
Jackaroo
Rodeo
VX Commodore
VU Utility
WH Statesman & Caprice
Corsa-B
Corsa-C
Astra-F
Astra-G
Rodeo
3 / 10
TFSPS005
Okay
Service Programming System (SPS)
Version 4.132
Turn off Ignition!
TFSPS006
Service Programming System (SPS)
Version 4.132
Ignition switched off!
TFSPS007
Okay
10.Turn OFF all power consuming devices!
(i.e. A/C Headlamps etc).
• Turn ON ignition!
• Engine OFF and ignition ON?
• Press the Okay soft key to continue.
11. The TECH 2 will then read and display the Vehicle
Identification Number (VIN) and ECU data. When
the TECH 2 screen opposite is displayed;
• Turn OFF TECH 2.
• Turn OFF ignition.
• Disconnect TECH 2 from the DLC.
• NOTE: If programming a Service Replacement PCM
the VIN number will not be displayed.
12.Connect the RS-232 cable (1) to TECH 2 RS-232
communication port. Connect the other end of the
RS-232 cable to the DB-9 adapter (2) and then con-
nect the DB-9 adapter to the 25/9 pin adapter. Con-
nect the 25/9 pin adapter to the Hardware Key and
then connect the Hardware Key to the serial port of a
Personal Computer (PC) with TIS 2000 installed.
•NOTE: If your PC has a 9 pin serial communication
port you will need to fit the 9/25 pin adapter between
the Hardware Key and the serial port of the TIS PC.
Connect the power supply (3) to the TECH 2 power
supply jack . Press the PWR button to turn on TECH
2. TECH 2 should now be at the title display screen.
Okay
Service Programming System (SPS)
Version 4.132
Turn on Ignition!
Engine off and Ignition on!
Turn off all power consuming devices!
TFSPS008
More
Service Programming System (SPS)
Version 4.132
Turn off Ignition! Disconnect Tech 2
from vehicle and connect it to TIS
Existing ECU Data!
VIN:
System:
Hardware:
Software:
JAATFS77H27103726
4JHI
97255155.2
BOS 01D001
TFSPS009
2
3
TE
CH 2
1
TFSPS014
13.Open TIS 2000 by double-clicking the TIS 2000 Icon.
14.The default user of TIS2000 is called "TIS". This user
does not have a password. Click the "OK" icon to
continue.
15.From the TIS 2000 Main Menu click on the SPS icon
to start the SPS application.
NOTE: If TIS 2000 does not detect a Hardware Key
the following error message will be displayed.
“Access to Service Programming Server was
denied. No Hardware Key was found!”
16.At Select Diagnostic Tool and Programming
Process click on desired selections for:
• Diagnostic tool being used: TECH 2. Whether you
are reprogramming an existing control unit or pro-
gramming a new control unit.
• Select ECU location: Vehicle.
17.After making your selections, select Next>.
18.At this point you should have already Requested
Info from the Vehicle and TECH 2 should be con-
nected to the serial port of a Personal Computer
(PC) with TIS 2000 installed via the Hardware Key.
19.Select Next>. to continue.
20.If a Service ECU has been installed the warning
opposite will be displayed at this time, select OK to
continue.
21.Confirm VIN or enter correct VIN, if required, then
select Next >.
22.Validate vehicle data, and change if necessary using
the pull down menus.
23.Select Next >.
24.A Summary screen will appear, allowing you to con-
firm your selection. Select Reprog to continue.
25.A Transfer Data screen will appear. Select Reprog
to initiate download of new calibration file to TECH 2.
The screen will track progress of download.
26.After download is complete a screen will appear
instructing you to connect TECH 2 to the vehicle to
complete programming process. Close the SPS
application to return to TIS 2000 main menu; power
down and then disconnect TECH 2 from PC.
27.Return to the vehicle and complete the SPS process.
28.Reconnect TECH 2 to the DLC.
29.Press the TECH 2 PWR button to turn on TECH
When the TECH 2 title screen is displayed, press
ENTER to continue.
30.Select F1: Service Programming System (SPS).
31.F1: Program ECU will be flashing. TECH 2 is ready
for ECU programming.
Select F1: Program ECU and follow the instructions on
the TECH 2 screen.
32.Turn OFF all power consuming devices!
(i.e. A/C, headlamps etc.).
• Turn On ignition
• Engine off and ignition on?
• Press the Okay soft key to continue.
Main Menu
TFSPS001
F0: Diagnostics
F1: Service Programming System (SPS)
F2: View Capture Data
F3: Tool Options
F4: Download/Upload Help
Service Programming System (SPS)
Version 4.132
Tech 2 is ready is ready for ECU programming!
TFSPS010
F0: Request Info
F1: Program ECU
Okay
Service Programming System (SPS)
Version 4.132
Turn on Ignition!
Engine off and Ignition on!
Turn off all power consuming devices!
TFSPS008
33.Tech 2 will begin programming the ECU. The screen
display will indicate the VIN Number, the New End
Model Number and the progress of the download as
a percentage.
•NOTE: The End Model Number will vary depending
on the application and software level.
34.Programming successful will be displayed when
programming is completed.
• Press the Exit soft key to continue.
• Programming has been completed.
• Turn off and disconnect Tech 2
• Turn off ignition.
35.Turn the ignition ON. Should the ‘CHECK ENGINE’
lamp be flashing at a rate of 4 times per second
(4Hz), it will be necessary to ‘link’ the ECU with the
Immobiliser Control Unit (ICU). Refer to Sections 11A,
11B or 11C.
More
Service Programming System (SPS)
Version 4.132
Turn off Ignition! Disconnect Tech 2
from vehicle and connect it to TIS
Existing ECU Data!
VIN:
System:
Hardware:
Software:
JAATFS77H27103726
4JH1
97255155.2
BOS 01D001
TFSPS011
Service Programming System (SPS)
Version 4.132
Programming Successful
Press [Exit] Key
TFSPS012