holden.wiki

• MODEL SELECTION INDEX
• TF RODEO
• SECTION 7C - AUTOMATIC TRANSMISSION (AW30-40LE)
  • GENERAL DESCRIPTION
    • CONSTRUCTION
    • ELECTRONIC CONTROL COMPONENTS
    • TRANSMISSION CONTROL MODULE (TCM)
    • CONTROL SYSTEM DIAGRAM
    • CONTROL AND FUNCTIONS
    • MAJOR INPUT/OUTPUT COMPONENTS
    • LOCATION OF CLUTCH, BRAKE, ONE-WAY CLUTCH AND SOLENOID
    • OPERATION OF CLUTCH, BRAKE AND ONE-WAY CLUTCH
    • SPEED CHANGE AND LOCK-UP PATTERN
    • OVERDRIVE AND LOCK-UP OPERATING CONDITIONS
  • DIAGNOSIS
    • BASIC TROUBLESHOOTING
    • SELF DIAGNOSIS
    • DIAGNOSIS WITH TECH 2
    • USING TECH 2 ON THE VEHICLE
    • CONNECTING TECH 2 TO THE VEHICLE
    • TRANSMISSION DATA
    • TCC DATA
    • INTERMITTENT CONDITIONS
    • IDENTIFICATION OF TRANSMISSION CONTROL MODULE (TCM)
    • DIAGNOSTIC TROUBLE CODES (DTC) CHECK
    • DTC P0120 (FLASHING CODE 21) ANALOG THROTTLE SIGNAL FAILURE (VTH) (FOR UBS)
    • DTC P0502 (FLASHING CODE 24) SPEED METER SENSOR FAILURE (SP1)
    • DTC P0705 (FLASHING CODE 17) GEAR SELECTOR FAILURE (PRND2L)
    • DTC P0710 (FLASHING CODE 16) OIL TEMPERATURE SENSOR FAILURE (OT2)
    • DTC P0717 (FLASHING CODE 14) INPUT REVOLUTION SENSOR FAILURE (NC0)
    • DTC P0722 (FLASHING CODE 11) OUTPUT REVOLUTION SENSOR FAILURE (SP2)
    • DTC P0727 (FLASHING CODE 13) ENGINE REVOLUTION SIGNAL FAILURE (NE)
    • DTC P0743 (FLASHING CODE 33) TORQUE CONVERTER CLUTCH CONTROL LOCK-UP (ON/OFF) SOLENOID FAILURE (SL)
    • DTC P0748 (FLASHING CODE 35) PRESSURE CONTROL SOLENOID FAILURE (STH)
    • DTC P0753 (FLASHING CODE 31) SOLENOID 1 FAILURE (S1)
    • DTC P0758 (FLASHING CODE 32) SOLENOID 2 FAILURE (S2)
    • DTC P1120 (FLASHING CODE 22) PWM THROTTLE SIGNAL FAILURE (TH) (For TFR/S)
    • DTC P1121 (FLASHING CODE 23) ANALOG THROTTLE SIGNAL FAILURE (VREF, VGND)(For UBS)
    • WIRING DIAGRAM
    • CONNECTOR LIST
    • TROUBLESHOOTING CHART
    • MANUAL SHIFTING TEST
    • STALL TEST
    • TIME LAG TEST
    • HYDRAULIC TEST
    • ROAD TEST
    • SHIFT POINT CHART AND LOCK-UP POINT CHART
    • TCM VOLTAGE CHECK
  • ON-VEHICLE SERVICE
    • TRANSIMISSION FLUID LEVEL AND CONDITION
    • ATF REPLACEMENT
    • NEUTRAL START SWITCH INSPECTION
    • BRAKE SIGNAL INSPECTION
    • VEHICLE SPEED SENSOR INSPECTION
    • INPUT AND OUTPUT REVOLUTION SENSOR INSPECTION
    • PATTERN SELECT SWITCH INSPECTION
    • OVERDRIVE SWITCH INSPECTION
    • SOLENOID INSPECTION
    • ATF TEMPERATURE SENSOR INSPECTION
    • THROTTLE POSITION SENSOR INSPECTION (UBS and TFR/S)
    • SELECTOR LEVER
    • TRANSMISSION CONTROL MODULE (TCM)
    • SHIFT SOLENOID AND LOCK-UP SOLENOID
    • VALVE BODY ASSEMBLY AND PRESSURE CONTROL SOLENOID
    • REAR OIL SEAL (ADAPTER HOUSING, 4X4)
    • REAR OIL SEAL (EXTENSION HOUSING, 4X2)
    • TRANSMISSION REMOVAL AND INSTALLATION (UBS)
    • TRANSMISSION REMOVAL AND INSTALLATION (TFR/S)
  • UNIT REPAIR
    • MAJOR COMPONENTS
    • DISASSEMBLY OF MAJOR COMPONENTS (1)
    • REASSEMBLY OF MAJOR COMPONENTS (1)
    • DISASSEMBLY OF MAJOR COMPONENTS (2)
    • REASSEMBLY OF MAJOR COMPONENTS (2)
    • DISASSEMBLY OF MAJOR COMPONENTS (3)
    • REASSEMBLY OF MAJOR COMPONENTS (3)
    • DISASSEMBLY, INSPECTION AND REASSEMBLY OF MINOR COMPONENTS
    • OIL PUMP
    • OD PLANETARY GEAR AND OD DIRECT CLUTCH ASSEMBLY (C-0) Disassembly steps 1. OD direct clutch assembly 2. OD planetary gear assembly 3. Thrust bearing 4. Snap ring 5. Flange, disk and plate 6. Snap ring 7. Piston return spring 8. OD direct clutch pi
    • OD SUPPORT ASSEMBLY
    • DIRECT CLUTCH ASSEMBLY (C-2)
    • FORWARD CLUTCH ASSEMBLY (C-1)
    • FRONT PLANETARY GEAR
    • PLANETARY SUN GEAR AND NO.1 ONE-WAY CLUTCH
    • SECOND BRAKE ASSEMBLY (B-2)
    • REAR PLANETARY GEAR ASSEMBLY AND OUTPUT SHAFT
    • FIRST AND REVERSE BRAKE (B-3) Disassembly steps 1. Thrust bearing and race 2. Snap ring 3. Piston return spring 4. First and reverse brake piston No.2 5. O-ring
    • TRANSMISSION VALVE BODY ASSEMBLY
    • LOWER VALVE BODY
    • UPPER VALVE BODY
    • TRANSMISSION CASE
    • TORQUE CONVERTER
    • ADAPTER HOUSING (4X4)
    • EXTENSION HOUSING (4X2)
  • MAIN DATA AND SPECIFICATIONS
    • GENERAL SPECIFICATIONS
    • TORQUE SPECIFICATIONS
  • SPECIAL TOOLS