holden.wiki

• Model Selection Index
• RA Rodeo
• Section 6C1-3 Engine Management – V6 – Service Operations
  • 1 General Information
    • 1.1 General Description
    • 1.2 Service Precautions and Requirements
      • Service Precautions
      • Service Requirements
        • Basic Knowledge Required
      • Basic Diagnostic Tools Required
    • 1.3 Service Operations Not Covered In This Section
      • Air-conditioning System
      • Electrical Components
      • Fuel System
      • Transmission – Automatic
      • Transmission – Manual
    • 1.4 Warning Caution and Notes
      • Definition of WARNING, CAUTION and NOTE Statements
        • WARNING defined
        • CAUTION defined
        • NOTE defined
  • 2 General Service Operations
    • 2.1 Accelerator Pedal Position Sensor
      • Remove
      • Reinstall
    • 2.2 Air Cleaner Assembly
      • Air Cleaner Upper Housing
        • Remove
        • Reinstall
      • Air Cleaner Lower Housing Assembly
        • Remove
        • Reinstall
    • 2.3 Barometric Pressure Sensor
      • Remove
      • Reinstall
    • 2.4 Camshaft Position Sensor
      • Remove
      • Reinstall
    • 2.5 Crankshaft Position Sensor
      • Remove
      • Test
        • Resistance Check
      • Reinstall
    • 2.6 Engine Coolant Temperature Sensor
      • Remove
      • Test
        • Resistance Check
      • Reinstall
    • 2.7 Engine Control Module
      • Remove
      • Reinstall
      • ECM Reset
    • 2.8 Engine Control Module Bracket Assembly
      • Remove
      • Reinstall
    • 2.9 Engine Oil Level and Temperature Sensor
      • Remove
      • Test
        • Engine Oil Level Sensor Check
      • Reinstall
    • 2.10 Engine Oil Pressure Sensor
      • Remove
      • Reinstall
    • 2.11 Evaporative Emission (EVAP) Canister Purge Valve Quick
      • Disconnect
        • Locking Lever Type
        • Latch Type
        • Connect
    • 2.12 Evaporative Emission Canister Purge Valve
      • Remove
      • Test
        • Resistance Check
        • Functional Test
      • Reinstall
    • 2.13 Fuel Rail Assembly
      • Remove
      • Disassemble
        • Fuel Injector
        • Fuel Injector Wiring Harness Assembly
      • Reinstall
    • 2.14 Heated Oxygen Sensor
      • Service Precautions
        • Six Wire Sensor
        • Four Wire Sensor
      • Test
        • Heater Resistance Check – Six Wire HO2S
        • Heater Resistance Check – Four Wire HO2S
    • 2.15 Ignition Coil
      • Ignition Coils
        • Remove
        • Disassemble
        • Reassemble
        • Test
        • Reinstall
    • 2.16 Intake Air Duct Assembly
      • Remove
      • Reinstall
    • 2.17 Intake Air Temperature Sensor
      • Test
        • Resistance Check
    • 2.18 Knock Sensor, Bank 2 (LHS)
      • Remove
      • Reinstall
    • 2.19 Knock Sensor, Bank 1 (RHS)
      • Remove
      • Reinstall
    • 2.20 Mass Air Flow Sensor
      • Handling Precautions
      • Remove
      • Reinstall
    • 2.21 Schrader Valve – Fuel Pressure Gauge Connection Point
      • Remove
      • Reinstall
    • 2.22 Spark Plugs
      • Service Precautions
      • Remove
      • Inspect
      • Spark Plug Inspection
        • Poor Spark Plug Performance
        • Analysis of Spark Plug Condition
      • Reinstall
    • 2.23 Throttle Body Assembly
      • Handling Precautions
      • Remove
      • Inspect
      • Reinstall
  • 3 Specifications
  • 4 Assembly Lubricants
  • 5 Torque Specifications
  • 6 Special Tools