SECTION 6C3-6 - SPECIAL TOOLS - GEN III V8 PCM
TOOL NO. REF. IN TEXT TOOL DESCRIPTION COMMENTS
SD28018
OR AU338
FUEL PRESSURE
GAUGE - HIGH
PRESSURE
USED FOR CHECKING
SYSTEM FUEL PRESSURE IN
CONJUNCTION WITH AU453.
MANDATORY
CLASSIFICATION
ST-8329
INJECTOR TEST LIGHT
USED TO CHECK FOR
POWER AND THE CONTROL
CIRCUIT OF THE FUEL
INJECTOR FOR PROPER
OPERATION.
7434
COUPLER
MUST BE USED IN
CONJUNCTION WITH TOOL
NO. SD28057, COUPLER FOR
CHECKING FUEL PRESSURE.
MANDATORY
CLASSIFICATION
BT-8515
EXHAUST BACK
PRESSURE GAUGE
(WITH ADAPTER)
USED TO TEST FOR
PLUGGED OR RESTRICTED
EXHAUST COMPONENTS,
PARTICULARLY THE
CATALYTIC CONVERTER.
TOOL NO. REF. IN TEXT TOOL DESCRIPTION COMMENTS
J 33095
MICRO-PACK TERMINAL
REMOVER
USED FOR REMOVING
TERMINALS FROM MICRO-
PACK CONNECTORS (PCM).
J 28742 OR J 36400-5
WEATHER PACK
TERMINAL REMOVER
USED FOR REMOVING
TERMINALS FROM
WEATHER-PACK
CONNECTORS.
7000086I
TECH 2 SCAN TOOL
A HAND-HELD SCAN TOOL
USED TO ANALYZE AND
DIAGNOSE FUEL AND
EMISSION SYSTEM. ALSO
CAN BE USED TO ANALYZE
OTHER COMPUTER
SYSTEMS. THIS TECH 2
SCAN TOOL IS SIMILAR TO
THE PREVIOUSLY RELEASED
TECH 1, BUT WITH MORE
FUNCTIONS AND
CAPABILITY.
J 39765
FUEL SENDER
LOCKNUT WRENCH
USED FOR REMOVAL OF THE
MODULAR FUEL SENDER
ASSEMBLY RETAINING RING.
TOOL NO. REF. IN TEXT TOOL DESCRIPTION COMMENTS
7370
QUICK CONNECT
RELEASE TOOL
FUEL RETURN LINE
5/16 HOSE
USED FOR RELEASING THE
QUICK CONNECT HOSES AT
THE DASH PANEL
CONNECTIONS ONCE THE
FUEL SYSTEM HAS BEEN
DEPRESSURISED.
MANDATORY
CLASSIFICATION.
7371
QUICK CONNECT
RELEASE TOOL
FUEL SUPPLY LINE
3/8 HOSE
USED FOR RELEASING THE
QUICK CONNECT HOSES AT
THE DASH PANEL
CONNECTIONS ONCE THE
FUEL SYSTEM HAS BEEN
DEPRESSURISED.
MANDATORY
CLASSIFICATION.
J 39200
DIGITAL MULTIMETER
(DMM)
DIGITAL MULTIMETER WITH
10 MEG OHM INPUT
IMPEDANCE.
MULTIMETER AND TEST
LIGHT MUST BE USED AS
SPECIFIED IN DIAGNOSIS
PROCEDURES.
THEY MUST NOT BE
INTERCHANGED.
J 23738
VACUUM PUMP (20 IN.
HG MINIMUM)
USE GAUGE TO MONITOR
MANIFOLD ENGINE VACUUM
AND USE THE HAND PUMP
TO CHECK SENSORS,
SOLENOIDS AND VALVES.
TOOL NO. REF. IN TEXT TOOL DESCRIPTION COMMENTS
ST-125 OR 7230
HEI TESTER
USED FOR CHECKING
AVAILABLE SECONDARY
IGNITION VOLTAGE.
J 35616-A
CONNECTOR TEST
ADAPTER KIT
USED FOR MAKING
ELECTRICAL TEST
CONNECTIONS IN CURRENT
WEATHER-PACK, METRI-
PACK AND MICRO-PACK
STYLE TERMINALS.
MANDATORY
CLASSIFICATION.
J 39775
TRANSMISSION JUMPER
HARNESS
USED TO MEASURE
ELECTRONIC COMPONENT
BAND CIRCUIT RESISTANCE
IN THE TRANSMISSION.
ALSO USED TO TEST THE
TRANSMISSION WIRING
HARNESS AND
POWERTRAIN CONTROL
MODULE DURING
DIAGNOSIS.
MANDATORY
CLASSIFICATION.
J 37027-A
IAC MOTOR ANALYZER
GEN3 0148
USED TO MANUAL OPERATE
AND CHECK THE IDLE AIR
CONTROL VALVE SYSTEM
OPERATION.
MANDATORY
CLASSIFICATION.
TOOL NO. REF. IN TEXT TOOL DESCRIPTION COMMENTS
J 37287
INLET AND RETURN
FUEL LINE SHUT-OFF
ADAPTERS
GEN 3 0150
USED IN CONJUNCTION
WITH THE FUEL PRESSURE
GAUGE FOR RESTRICTING
THE FUEL SUPPLY AND
RETURN LINES FOR
TESTING.
MANDATORY
CLASSIFICATION.
J 39021
FUEL INJECTOR
COIL/BALANCE TESTER
GEN3 0151
THIS TESTER IS USED IN
CONJUNCTION WITH A
DIGITAL MULTIMETER FOR
TESTING FUEL INJECTOR
COILS, AND CYLINDER
INJECTOR BALANCE
TESTING.
MANDATORY
CLASSIFICATION.
AU453
FUEL GAUGE
SCHRADER FITTING
ADAPTER
USED FOR CHECKING
SYSTEM FUEL PRESSURE IN
CONJUNCTION WITH
SD28018.
MANDATORY
CLASSIFICATION.
TOOL NO. REF. IN TEXT TOOL DESCRIPTION COMMENTS
J 34142-A
UNPOWERED TEST
LIGHT
USED FOR CHECKING
WIRING FOR COMPLETE
CIRCUIT, SHORT TO EARTH,
OR VOLTAGE.
MUST HAVE CURRENT
DRAW OF LESS THAN 0.3 A.
J 41712
OIL PRESSURE SENSOR
SOCKET
GEN3 0152
USED FOR REMOVING THE
OIL PRESSURE SENSOR
FROM THE ENGINE.
AU533
QUICK CONNECT
RELEASE TOOL
5/16 HOSE
3/8 HOSE
USED FOR RELEASING THE
QUICK CONNECT HOSE AT
THE CANISTER PURGE
SOLENOID (5/16 RED TOOL)
AND FUEL FILTER AND FUEL
FEED AND RETURN HOSES
QUICK CONNECTOR (3/8
BLUE TOOL).
MANDATORY
CLASSIFICATION.