Menu Holden Logo

holden.wiki
Home Main Menu
Home Main Menu
  • MODEL SELECTION INDEX
  • VX SERIES - COMMODORE, CALAIS SERVICE INFORAMTION
  • SECTION 7C5 - HYDRA-MATIC 4L60-E AUTOMATIC TRANSMISSION: UNIT REPAIR
    • 1. TRANSMISSION DISASSEMBLE
      • 1.1 GENERAL SERVICE INFORMATION
      • 1.2 TRANSMISSION PREPARATION
      • 1.3 2-4 SERVO ASSEMBLY
        • REMOVE
        • DISASSEMBLE
        • SERVO PIN LENGTH
      • 1.4 SPEED SENSOR AND CASE EXTENSION
      • 1.5 OIL PAN AND FILTER ASSEMBLY
      • 1.6 CONTROL VALVE BODY AND WIRING HARNESS
      • 1.7 CONVERTER HOUSING
      • 1.8 TRANSMISSION END PLAY CHECK
      • 1.9 OIL PUMP ASSEMBLY
      • 1.10 REVERSE INPUT CLUTCH, INPUT CLUTCH, 2-4 BAND AND INPUT GEAR SET
      • 1.11 REACTION GEAR SET
      • 1.12 LOW AND REVERSE CLUTCH ASSEMBLY
      • 1.13 INNER MANUAL SHAFT, LINKAGE AND SEAL
    • 2. COMPONENT DISASSEMBLE, INSPECTION, REASSEMBLE
      • 2.1 CASE
        • INSPECT
      • 2.2 THIRD ACCUMULATOR RETAINER AND BALL ASSEMBLY
        • INSPECT
        • REPLACE
      • 2.3 CASE BUSHING
        • REPLACE
      • 2.4 2-4 SERVO ASSEMBLY
        • INSPECT
      • 2.5 LOW AND REVERSE CLUTCH ASSEMBLY
        • INSPECT
        • SPACER PLATE SELECTION
      • 2.6 LOW AND REVERSE CLUTCH SUPPORT ASSEMBLY
      • 2.7 REACTION INTERNAL GEAR AND CARRIER ASSEMBLY
        • INSPECT
      • 2.8 REACTION SUN GEAR AND SHELL
        • INSPECT
        • SUN GEAR BUSH - REPLACE
      • 2.9 INPUT INTERNAL GEAR AND OUTPUT SHAFT
        • INSPECT
        • REACTION CARRIER SHAFT BUSHES - REPLACE
      • 2.10 TRANSMISSION OUTPUT SPEED SENSOR RING
        • REPLACE
      • 2.11 INPUT CARRIER AND SUN GEAR
        • INSPECT
        • INPUT SUN GEAR BUSHES - REPLACE
      • 2.12 INPUT CLUTCH HOUSING ASSEMBLY
        • DISASSEMBLE
        • INSPECT
        • FORWARD CLUTCH SPRAG ASSEMBLY
        • REASSEMBLE
        • INPUT CLUTCH HOUSING AIR CHECKS
        • REINSTALL TURBINE SHAFT SEALING RINGS
      • 2.13 REVERSE INPUT CLUTCH ASSEMBLY
        • DISASSEMBLE
        • INSPECT
        • REVERSE INPUT CLUTCH HOUSING BUSHES - REPLACE
        • REASSEMBLE
        • REVERSE INPUT CLUTCH AIR CHECK
      • 2.14 2-4 BAND
        • INSPECT
      • 2.15 OIL PUMP
        • DISASSEMBLE
        • INSPECT
        • OIL PUMP BUSHINGS – REPLACE
        • REASSEMBLE
        • OIL PUMP AIR CHECKS
      • 2.16 CONTROL VALVE BODY
        • DISASSEMBLE
        • INSPECT
        • SPACER PLATE EVALUATION
        • REASSEMBLE
    • 3. TRANSMISSION REASSEMBLE
      • 3.1 MANUAL SHAFT AND PARKING LINKAGE
      • 3.2 LOW AND REVERSE CLUTCH PISTON
      • 3.3 REACTION PLANETARY GEAR SET
      • 3.4 LOW AND REVERSE CLUTCH PLATES AND SUPPORT ASSEMBLY
      • 3.5 REACTION GEAR, INPUT GEAR AND OUTPUT SHAFT
      • 3.6 REVERSE INPUT CLUTCH, INPUT CLUTCH AND INPUT GEAR SET
      • 3.7 2-4 BAND ASSEMBLY
      • 3.8 OIL PUMP
      • 3.9 CONVERTER HOUSING
      • 3.10 CONTROL VALVE BODY AND ASSOCIATED COMPONENTS
      • 3.11 OIL FILTER AND OIL PAN
      • 3.12 CASE EXTENSION HOUSING AND SPEED SENSOR
        • INSPECT
        • CASE EXTENSION HOUSING BUSH - REPLACE
        • REINSTALL
      • 3.13 2-4 SERVO ASSEMBLY
        • SERVO PIN LENGTH - CHECK
        • REINSTALL
      • 3.14 NEUTRAL START & BACK-UP LAMP SWITCH ASSEMBLY
      • 3.15 TORQUE CONVERTER
        • INSPECT
        • END PLAY - CHECK
        • REINSTALL
      • 3.16 TRANSMISSION FIXTURE REMOVAL
    • 4. TRANSMISSION REFERENCE DIAGRAMS
    • 5. SPECIFICATIONS
    • 6. TORQUE WRENCH SPECIFICATIONS
    • 7. SPECIAL TOOLS
Made by Mibble ♥