holden.wiki

• MODEL SELECTION INDEX
• MY 2005 VZ Series - Service Information
• Section 6C3-3Powertrain Management GEN III V8 –Service Ope
  • 1 General Information
    • 1.1 General Description
    • 1.2 Service Precautions and Notes
  • 2 General Service Operations
    • 2.1 Service Operations Not Covered in This Section
      • Fuel System
      • Engine Dress Covers
    • 2.2 Fuel Injector Coil Test
      • Engine Coolant Temperature Between 10 - 35°C
      • Engine Coolant Temperature Outside 10 - 35°C
    • 2.3 Fuel Injector Balance Test
      • Fuel Injector Balance Test – With Tech 2
      • Fuel Injector Balance Test – Without Tech 2
        • Fuel Injector Pressure Drop Calculation
        • Fuel Injector Pressure Drop Analysis
    • 2.4 Fuel Injector Leak Down Test
    • 2.5 Power Balance Test
  • 3 Component Replacement
    • 3.1 Components Not Covered In This Section
      • Air-conditioning System
      • Electrical Components
      • Fuel System
      • Transmission – Automatic
      • Transmission – Manual
    • 3.2 Accelerator Pedal Position Sensor
      • Remove
      • Reinstall
    • 3.3 Accelerator Pedal Position Sensor Support Bracket
      • Remove
      • Reinstall
    • 3.4 Air Cleaner Assembly
      • Air Cleaner Upper Housing
        • Remove
        • Reinstall
      • Air Cleaner Lower Housing Assembly
        • Remove
        • Reinstall
    • 3.5 Camshaft Position Sensor
      • Remove
      • Reinstall
    • 3.6 Crankshaft Position Sensor
      • Remove
      • Reinstall
    • 3.7 Engine Coolant Temperature Sensor
      • Remove
      • Test
        • Resistance Check
      • Reinstall
    • 3.8 Engine Oil Pressure Sensor
      • Remove
      • Reinstall
    • 3.9 EVAP Canister Purge Solenoid Valve
      • Remove
      • Test
        • Resistance Check
        • Functional Test
      • Reinstall
    • 3.10 Fuel Pulse Dampener
      • Remove
      • Reinstall
    • 3.11 Fuel Rail Assembly
      • Remove
      • Disassemble
        • Fuel Injector Assembly
      • Reinstall
    • 3.12 Heated Oxygen Sensor
      • Service Precautions
      • Remove
      • Test
        • Heater Resistance Check
      • Reinstall
    • 3.13 Ignition Coil Assembly
      • Remove
      • Test
      • Reinstall
    • 3.14 Intake Air Temperature Sensor
      • Test
        • Resistance Check
    • 3.15 Knock Sensor
      • Remove
      • Reinstall
    • 3.16 Manifold Absolute Pressure Sensor
      • Remove
      • Reinstall
    • 3.17 Mass Air Flow Sensor and Intake Air Duct
      • Remove
      • Reinstall
    • 3.18 Powertrain Control Module
      • Remove
      • Reinstall
    • 3.19 Powertrain Control Module Bracket Assembly
      • Remove
      • Reinstall
    • 3.20 Schrader Valve – Fuel Pressure Test Point
      • Remove
      • Reinstall
    • 3.21 Spark Plugs
      • Service Precautions
      • Remove
      • Clean, Inspect and Adjust
      • Spark Plug Inspection
        • Poor Spark Plug Performance
        • Analysis of Spark Plug Condition
      • Reinstall
    • 3.22 Spark Plug Leads
      • Remove
      • Inspect
      • Reinstall
    • 3.23 Throttle Actuator Control Module
      • Remove
      • Reinstall
    • 3.24 Throttle Body Assembly
      • Handling Precautions
      • Remove
      • Inspect
      • Reinstall
  • 4 Specifications
  • 5 Torque Wrench Specifications
  • 6 Special Tools