holden.wiki

• MODEL SELECTION INDEX
• MY 2005 VZ Series - Service Information
• Section 7E5Hydra-Matic 5L40–E Automatic Transmission – Unit
  • 1 Transmission Disassemble
    • 1.1 General Service Information
      • Teflon Sealing Rings
      • Thrust Washer Surfaces
    • 1.2 Transmission Preparation
      • Torque Converter Assembly Removal
      • Holding Fixture Installation
      • Draining Transmission Fluid
    • 1.3 Extension Housing
      • Remove
    • 1.4 Pan and Filter Assembly
      • Removal
    • 1.5 Wiring Harness
      • Remove
    • 1.6 Control Valve Body and Accumulator Assembly
      • Remove
    • 1.7 Output Shaft Speed Sensor
      • Remove
    • 1.8 Input Speed Sensor
      • Remove
    • 1.9 Torque Converter Housing
      • Removal
    • 1.10 Direct and Reverse Clutch - Forward and Coast Clutch
      • Remove
    • 1.11 Input Sun Gear Shaft
      • Remove
    • 1.12 Direct Clutch Hub
      • Remove
    • 1.13 Intermediate Clutch Sprag Assembly
      • Remove
    • 1.14 Overdrive Clutch Housing
      • Remove
    • 1.15 Low Clutch Sprag
      • Removal
    • 1.16 Centre Support
      • Remove
    • 1.17 Input and Reaction Carrier
      • Remove
    • 1.18 Output Shaft
      • Remove
    • 1.19 Park System Components
      • Remove
    • 1.20 Transmission Case Assembly
      • Inspect
    • 1.21 Transmission Case Components
      • Disassemble
      • Reassemble
    • 1.22 Park System Components
      • Reinstall
    • 1.23 Output Shaft and Rear Internal Ring Gear
      • Disassemble
      • Reassemble
    • 1.24 Input and Reaction Carrier
      • Disassemble
      • Reassemble
    • 1.25 Centre Support
      • Disassemble
      • Reassemble
        • Alternative Reassembly Method
    • 1.26 Low Clutch Sprag
      • Reassemble
    • 1.27 Overdrive and Intermediate Clutch
      • Disassemble
      • Reassemble
    • 1.28 Intermediate Clutch Sprag
      • Inspect
      • Reassemble
    • 1.29 Direct Clutch Hub
      • Reassemble
    • 1.30 Input Sun Gear Shaft
      • Disassemble
      • Reassemble
    • 1.31 Forward and Coast Clutch
      • Disassemble
      • Reassemble
    • 1.32 Direct and Reverse Clutch
      • Disassemble
      • Reassemble
    • 1.33 Direct and Reverse Clutch - Forward and Coast Clutch
      • Reinstall
        • Alternative Reassembly Method
    • 1.34 Fluid Pump
      • Remove
      • Disassemble
    • 1.35 Torque Converter Seal
      • Remove
    • 1.36 Fluid Pump
      • Reassemble
    • 1.37 Torque Converter Housing
      • Reinstall
    • 1.38 Torque Converter Seal
      • Reinstall
    • 1.39 Control Valve Body and Accumulator Assembly
      • Disassemble
      • Rear Control Valve Body Inspection
      • Rear Control Valve Body Disassemble
      • Rear Control Valve Body Assemble
      • Front Control Valve Body Inspection
      • Front Control Valve Body Disassemble
      • Front Control Valve Body Assemble
      • Control Valve Body and Accumulator Assembly
        • Assemble
    • 1.40 Input Speed Sensor Installation
    • 1.41 Output Shaft Speed Sensor Installation
    • 1.42 Control Valve Body and Accumulator Assembly
      • Reinstall
    • 1.43 Wiring Harness
      • Reinstall
    • 1.44 Pan and Filter Assembly
      • Reinstall
    • 1.45 Extension Housing
      • Reinstall
    • 1.46 Propeller Shaft Flange
      • Reassemble
    • 1.47 Holding Fixture Removal
    • 1.48 Torque Converter Assembly
      • Reinstall
  • 2 Transmission Reference Diagrams
  • 3 Specifications
  • 4 Torque Wrench Specifications
  • 5 Special Tools