Menu Holden Logo

holden.wiki
Home Main Menu
Home Main Menu
  • MODEL SELECTION INDEX
  • MY2006 VZ Series - Service Information
  • Section 7D5 Automatic Transmission – 4L65E – Unit Repair
    • 1 General Information
      • 1.1 Service Information
      • 1.2 General Description
      • 1.3 Rebuilding Tips
        • Teflon Sealing Rings
          • Thrust Washer Surfaces
    • 2 Transmission Disassembly
      • 2.1 Transmission Preparation
      • 2.2 2 – 4 Servo Assembly
        • Remove
        • Disassemble
        • Servo Pin Length
      • 2.3 Speed Sensor and Extension Housing
        • Remove
      • 2.4 Oil Pan and Filter Assembly
        • Remove
      • 2.5 Control Valve Body And Wiring Harness
        • Remove
      • 2.6 Torque Converter Housing
        • Remove
      • 2.7 Transmission End Play Check
      • 2.8 Oil Pump Assembly
        • Remove
      • 2.9 Reverse Input Clutch, Input Clutch, 2-4 Band and Input G
        • Remove
      • 2.10 Reaction Gear Set
        • Remove
      • 2.11 Low and Reverse Clutch Assembly
        • Remove
      • 2.12 Manual Shaft, Inner Linkage and Seal
        • Remove
    • 3 Component Disassembly, Inspection, Reassembly
      • 3.1 Transmission Case
        • Inspect
      • 3.2 Third Accumulator Retainer and Ball Assembly
        • Inspect
        • Replace
      • 3.3 Transmission Case Bush
        • Replace
      • 3.4 2-4 Servo Assembly
        • Inspect
      • 3.5 Low and Reverse Clutch Assembly
        • Inspect
        • Spacer Plate Selection
      • 3.6 Low and Reverse Clutch
        • Support Assembly
      • 3.7 Reaction Internal Gear and Carrier Assembly
        • Inspect
      • 3.8 Reaction Sun Gear and Shell
        • Inspect
        • Sun Gear Bush – Replace
      • 3.9 Input Internal Gear and Output Shaft
        • Inspect
        • Reaction Carrier Shaft Bushes – Replace
      • 3.10 Transmission Output Speed Sensor Ring
        • Replace
      • 3.11 Input Carrier and Sun Gear
        • Inspect
        • Input Sun Gear Bushes – Replace
      • 3.12 Input Clutch Housing Assembly
        • Exploded View
        • Disassemble
          • 3 – 4 Clutch
          • Forward Clutch Assembly
          • Overrun Clutch Assembly
          • 3 – 4 Clutch Assembly
        • Inspect
        • Forward Clutch Sprag Assembly
          • Disassemble
          • Inspect
          • Reassemble
        • Reassemble
          • 3-4 Clutch Assembly
          • Overrun Clutch Assembly
          • Forward Clutch Assembly
          • 3-4 Clutch
        • Input Clutch Housing Air Checks
        • Reinstall Turbine Shaft Sealing Rings
      • 3.13 Reverse Input Clutch Assembly
        • Disassemble
        • Inspect
        • Reverse Input Clutch Housing Bushes – Replace
        • Reassemble
        • Reverse Input Clutch Air Check
      • 3.14 2-4 Band
        • Inspect
      • 3.15 Oil Pump Assembly
        • Disassemble
          • Oil Pump Assembly
          • Oil Pump Body
          • Input Speed Sensor
          • Oil Pump Cover
        • Inspect
        • Oil Pump Bushes – Replace
          • Pump Body Bush
          • Pump Cover Bushes
        • Reassemble
          • Oil Pump Body
          • Oil Pump Cover
          • Input Speed Sensor
          • Oil Pump Assembly
        • Oil Pump Air Checks
          • Introduction
          • Air Checks Table
      • 3.16 Control Valve Body
        • Exploded Views
          • View A
          • View B
        • Disassemble
        • Clean and Inspect
          • Control Valve Body
          • Spacer Plate Evaluation
        • Reassemble
    • 4 Transmission Reassembly
      • 4.1 Manual Shaft, Inner Linkage and Seal
        • Reinstall
      • 4.2 Low and Reverse Clutch Piston
        • Reinstall
      • 4.3 Reaction Planetary Gear Set
        • Reinstall
      • 4.4 Low and Reverse Clutch Plates and Support Assembly
        • Reinstall
      • 4.5 Reaction Gear, Input Gear and Output Shaft
        • Reinstall
      • 4.6 Reverse Input Clutch, Input Clutch and Input Gear Set
        • Reinstall
      • 4.7 2-4 Band Assembly
        • Reinstall
      • 4.8 Oil Pump
        • Reinstall
      • 4.9 Torque Converter Housing
        • Reinstall
      • 4.10 Control Valve Body and Wiring Harness
        • Reinstall
      • 4.11 Oil Filter and Oil Pan
        • Reinstall
      • 4.12 Extension Housing and Speed Sensor
        • Inspect
        • Extension Housing Bush – Replace
        • Reinstall
      • 4.13 2-4 Servo Assembly
        • Servo Pin Length – Check
        • Reassemble
        • Reinstall
      • 4.14 Neutral Start & Back-Up Lamp Switch Assembly
        • Reinstall
      • 4.15 Torque Converter
        • Inspect
        • End Play Check
        • Reinstall
      • 4.16 Transmission Fixture Removal
    • 5 Transmission Diagrams
      • 5.1 Transmission Case and External Parts
      • 5.2 Control Valve Body Assembly
      • 5.3 Control Valve Identification
      • 5.4 Control Valve Spring Identification
      • 5.5 Seal Location and Orientation
      • 5.6 Bush/Bearing Location and Orientation
    • 6 Specifications
    • 7 Torque Wrench Specifications
    • 8 Special Tools
Made by Mibble ♥