holden.wiki

• MODEL SELECTION INDEX
• MY2005 & MY2006 WL Series - Service Information
• Section 12P Wiring Diagrams
  • 1 General Information
  • 2 Electrical Circuit Diagnosis
    • Step 1 Identify the Problem
    • Step 2 Specify the Problem
    • Step 3 Investigate the Problem
    • Step 4 Develop Possible Causes
    • Step 5 Isolate the Most Possible Cause
    • Step 6 Verify
    • Problem Example
      • Step 1 Identify the Problem
      • Step 2 Specify the Problem
      • Step 3 Investigate the Problem
      • Step 4 Develop Possible Causes
      • Step 5 Isolate the Most Possible Cause
      • Step 6 Verify
  • 3 Test Procedures
    • 3.1 Electrical Fault Diagnosis
      • Possible Electrical Malfunctions
      • Circuit Faults
        • Open
        • Short to Earth
        • Short to Voltage
        • High Resistance Problems
    • 3.2 Troubleshooting Test Equipment
      • Jumper Wire
      • Test Light
      • Self-Powered Test Light
      • Multimeters
    • 3.3 Digital Multimeter
      • Use Of A Multimeter
      • Selection Of Multimeters
      • Voltage Measurement
      • Resistance Measurement
        • Resistance Testing
      • Continuity Testing
      • Diode Testing
      • Current Measurement
  • 4 Diagnostic Tests
    • 4.1 Testing For Voltage
    • 4.2 Testing For Continuity
    • 4.3 Testing For Voltage Drop
    • 4.4 Testing For Short To Earth
      • Using A Test Light Or Voltmeter
      • Using A Self-Powered Test Light Or Ohmmeter
      • Using A Short Finder
      • Using A Compass
      • Using A Circuit Breaker
    • 4.5 Operating A Short Finder
      • Measuring Current
    • 4.6 Detecting Intermittent Electrical Faults
      • Diagnostic Procedure
      • Checking Terminal Contact
      • Meter Connections
        • Additional Information
  • 5 Wiring Repair Procedures
    • 5.1 General Information
    • 5.2 Performing Wiring Harness Repairs
      • Soldering
      • The Five Points To Soldering
        • Step 1 Soldering Preparation
        • Step 2 Iron Preparation
        • Step 3 Forming a Heat Bridge
        • Step 4 Soldering Iron Removal
        • Step 5 Prevent Job Movement
      • Joining Wire
        • Twist Joint
        • Splice Joint
        • The Y Junction
        • The T Junction
    • 5.3 Splicing Wiring Using Splice Clips
      • Step 1 Open the Harness
      • Step 2 Cut the Wire
      • Step 3 Select the Correct Size and Type of Wire
      • Step 4 Strip the Insulation
        • Metric Size
        • AWG
      • Step 5 Crimping the Joint
      • Step 6 Solder
      • Step 7 Tape the Splice
    • 5.4 ABS And SRS Wiring Repair
      • ABS And SRS Wire Pigtail Repair
      • Wiring Repair
        • Step 1 Open the Harness
        • Step 2 Cut the Wire
        • Step 3 Select the Correct Size and Type of Wire
        • Step 4 Strip the Insulation
        • Step 5 Select and Position the Splice Sleeve
        • Step 6 Insert First Wire Into Splice Sleeve and Crimp
        • Step 7 Crimp the Second Wire in the Splice
        • Step 8 Shrink the Insulation around the Splice
        • Step 9 Close the Harness
      • ABS And SRS Wiring Splice Repair
    • 5.5 Splicing Twisted Or Shielded Cable
      • Step 1 Strip the Cable
      • Step 2 Prepare the Splice
      • Step 3 Reassemble the Cable
      • Step 4 Tape the Joint
    • 5.6 Splicing In-Line Harness Diodes
      • Step 1 Open the Harness
      • Step 2 Remove Diode
      • Step 3 Install the New Diode
    • 5.7 Heated Oxygen Sensor (HO2S) Wiring Repairs
    • 5.8 Terminal Removal
      • Push to Seat Connectors
      • Pull-to-Seat Connectors
        • Repairing Push-ToSeat And PullToSeat Connectors
      • Weather Pack® Connectors
  • 6 Reading 12P Wiring Diagrams
    • General Information
    • Sheet Identification
    • Wire Identification
    • Wire Colour Abbreviations
    • Wiring Harness Abbreviations
    • Wiring Harness Visual Identification
    • Connectors
    • Grid Reference
    • Continuation Reference
    • Multiple Continuation References
    • Assembly Identification
    • Assembly Legend
    • Assembly Continuation
    • Assembly Connector Identification
    • Assembly Circuit Identification
    • Information Within An Assembly
    • Harness Splices
    • Ground Locations
    • Circuit Symbols
  • 7 Connector Location Illustrations
  • 8 Electrical Schematics Contents
  • 9 Module Location Charts
    • Electrically Operated Mechanical Devices
    • Indicators, Alarms and Signal Devices
    • Inductors
    • Measurement, Display and Test Devices
    • Modules, Systems and Sub-Assemblies
    • Motors
    • Other Devices and Equipment
    • Power Supplies
    • Regulators and Amplifiers
    • Resistors
    • Semi Conductors
    • Switches
    • Transducers
    • Transmission Paths, Conductors and Antennas
  • 10 Special Tools