holden.wiki

• MODEL SELECTION INDEX
• MY 2005 WL Series - Service Information
• Section 5A Service and Park Braking Systems
  • 1 General Information
    • 1.1 General Description
    • 1.2 Master Cylinder
      • Description
      • Construction
      • Operation
    • 1.3 Vacuum Brake Booster
      • Description
      • Construction
      • Operation
        • Mechanical Brake Assist (MBA)
    • 1.4 Front and Rear Brake Calipers
    • 1.5 Brake Pipes and Hoses
      • Description
  • 2. Minor Service Operations
    • 2.1 Service Warnings, Cautions and Notes
    • 2.2 Park Brake Cable, Adjust
    • 2.3 Brake Fluid Level Check
    • 2.4 Brake System Bleed
    • 2.5 Brake Fluid, Change
      • Draining Master Cylinder
      • Draining Brake Calipers
    • 2.6 Brake Pad Wear, Check
      • Front or Rear
    • 2.7 Brake Pads, Replace
      • Preparation
      • Front Brake Pads
        • Remove
        • Installation
      • Rear Brake Pads
        • Remove
        • Reinstall
      • Brake Pad Bedding-In Procedure
    • 2.8 Brake Pedal Assembly
      • Remove
      • Disassemble
      • Reassemble
      • Reinstall
    • 2.9 Park Brake Lever
      • Remove
      • Reinstall
    • 2.10 Park Brake Warning Lamp Switch
      • Remove
      • Inspect
      • Reinstall
    • 2.11 Front Park Brake Cable
      • Remove
      • Reinstall
    • 2.12 Rear Park Brake Cable/s
      • Remove
      • Reinstall
    • 2.13 Front Caliper Brake Hose
      • Remove
      • Reinstall
    • 2.14 Rear Caliper Brake Hose
      • Remove
      • Reinstall
    • 2.15 Rear Brake Hoses
      • Remove
      • Reinstall
    • 2.16 Brake Booster Hose & Valve Assembly – V6 Engine
      • Replace
    • 2.17 Brake Booster Hose & Valve Assembly – GEN III V8 Engine
      • Replace
    • 2.18 Brake Fluid Level Switch
      • Test
      • Replace
  • 3 Major Service Operations
    • 3.1 Master Cylinder
      • Remove
      • Reinstall
    • 3.2 Brake Master Cylinder Reservoir
      • Replace
    • 3.3 Brake Booster
      • Remove
      • Reinstall
    • 3.4 Front Brake Caliper
      • Remove
      • Disassemble
      • Clean and Inspect
      • Reassemble
      • Reinstall
    • 3.5 Rear Brake Caliper
      • Remove
      • Disassemble
      • Clean and Inspect
      • Reassemble
      • Reinstall
    • 3.6 Front Brake Disc
      • Remove
      • Inspect
      • Front Brake Disc and Hub Indexing Procedure
        • Part 1. Clean Mating Surfaces
        • Part 2. Indexing Brake Disc to Hub
        • Part 3. Hub Runout Check
      • Reinstall
    • 3.7 Rear Brake Disc
      • Remove
      • Inspect
        • All Models
      • Rear Brake Disc and Hub Indexing Procedure
        • Part 1 Clean Mating Surfaces
        • Part 2 Indexing Brake Disc to Hub
        • Part 3 Trunnion Hub Runout Check
      • Reinstall
    • 3.8 Park Brake Lining Wear, Check
    • 3.9 Park Brake Shoe, Adjust
    • 3.10 Park Brake Shoe
      • Remove
      • Reinstall
    • 3.11 Front Disc Brake Shield
    • 3.12 Rear Disc Brake Dust Shield
      • Remove
      • Reinstall
  • 4. Diagnosis
  • 5 Specifications
  • 6 Torque Wrench Specifications
  • 7 Special Tools