holden.wiki

• MODEL SELECTION INDEX
• MY2006 WL Series - Service Information
• Section 6C4–3 Engine Management GEN IV V8 – Service Operations
  • 1 General Information
    • 1.1 General Description
    • 1.2 Service Precautions and Notes
  • 2 General Service Operations
    • 2.1 Service Operations Not Covered In This Section
      • Fuel System Cleaning
      • Fuel System Leak and Pressure Test
      • Fuel Feed Hose to Fuel Rail
      • Fuel Line Quick Connect Fittings
    • 2.2 Engine Dress Covers
      • Remove
      • Reinstall
    • 2.3 Fuel Injector Coil and Balance Test
    • 2.4 Fuel Injector Leak Down Test
  • 3 Component Replacement
    • 3.1 Components Not Covered In This Section
      • Automatic Transmission Components
      • A/C Pressure Switch
      • Brake Pedal Switches
      • Clutch Pedal Switches
      • Cruise Control Switch Assembly
      • Evaporative Emission Control Canister
      • Fuel Filter
      • Fuel Hose/Pipes
      • Fuel Pump Motor Assembly and Fuel Pressure Regulator
      • Fuel Sender Assembly
      • Fuel Tank Pressure Sensor
      • Fuses and Relays
      • Manual Transmission Components
      • Neutral Start and Back-up Lamp Switch
      • Powertrain Interface Module (PIM)
      • Vehicle Speed Sensor
    • 3.2 Accelerator Pedal Position (APP) Sensor
      • Remove
      • Reinstall
    • 3.3 Accelerator Pedal Position (APP) Sensor Support Bracket
      • Remove
      • Reinstall
    • 3.4 Air Cleaner Assembly
      • Air Cleaner Upper Housing
        • Remove
        • Reinstall
      • Air Cleaner Lower Housing
        • Remove
        • Reinstall
    • 3.6 Camshaft Position (CMP) Sensor
      • Removal Procedure
      • Installation Procedure
    • 3.7 Crankshaft Position (CKP) Sensor
      • Remove
      • Reinstall
    • 3.7 Engine Control Module (ECM)
      • Remove
      • Reinstall
    • 3.8 Engine Control Module (ECM) Bracket Assembly
      • Remove
      • Reinstall
    • 3.9 Engine Coolant Temperature (ECT) Sensor
      • Remove
      • Test
        • Resistance Check
      • Reinstall
    • 3.10 Engine Oil Pressure (EOP) Sensor
      • Remove
      • Reinstall
    • 3.11 EVAP Canister Purge Solenoid Valve
      • Remove
      • Reinstall
    • 3.12 Fuel Rail Assembly
      • Remove
        • Disassemble
        • Reassemble
      • Reinstall
    • 3.13 Heated O2 Sensors
      • Service Precautions
      • Remove
      • Reinstall
      • Test
        • Heater Resistance Check
    • 3.14 Ignition Coil / Module
      • Remove
      • Test
      • Reinstall
    • 3.15 Intake Air Temperature (IAT) Sensor
      • Test
        • Resistance Check
    • 3.16 Knock Sensors
      • Remove
      • Reinstall
    • 3.17 Manifold Absolute Pressure (MAP) Sensor
      • Remove
      • Reinstall
    • 3.18 Mass Air Flow (MAF) Sensor and Intake Air Duct
      • Remove
      • Reinstall
    • 3.19 Spark Plugs
      • Service Precautions
      • Remove
      • Clean, Inspect and Adjust
      • Spark Plug Inspection
        • Poor Spark Plug Performance
        • Analysis of Spark Plug Condition
      • Reinstall
    • 3.20 Spark Plug Leads
      • Remove
      • Inspect
      • Reinstall
    • 3.21 Throttle Body
      • Handling Precautions
      • Remove
      • Inspect
      • Reinstall
  • 4 Specifications
  • 5 Torque Wrench Specifications
  • 6 Special Tools