holden.wiki

• MODEL SELECTION INDEX
• MY 2005 WL Series - Service Information
• Section 9 Steering
  • 1 General Information
    • 1.1 General Description – Power Steering Rack and Pinion
      • Principles of Operation
      • Power Steering Fluid Flow
        • Neutral Position – Straight Ahead
        • Turning Right
        • Turning Left
        • Inner Rotating Valve
    • 1.2 General Description – Power Steering Pump Assembly
      • Location and Mounting
        • V6 Engine
        • GEN III V8 Engine
      • Pump Construction
        • Thrust Plate
        • Pump Ring
        • Rear Plate
        • Drive Shaft and Rotor
      • Operation
    • 1.3 Filling the Pump
    • 1.4 General Description – Steering Column
      • Cautionary Notes
  • 2 Diagnosis
    • 2.1 General Diagnostic Information
    • 2.2 Hydraulic System Pressure Test
      • Procedure
    • 2.3 Hydraulic System Leak Test
      • General Procedure
        • External Leakage Check
      • Power Steering Pump Leak Test
      • Steering Gear
      • Seal Replacement Recommendations
    • 2.4 Power Steering Pump Diagnostic Check
  • 3 Service Operations
    • 3.1 Steering Wheel Assembly
      • Remove
      • Disassemble
        • Rear Cover
        • Steering Wheel Inflatable Restraint Retaining Clip
        • Horn Bar Stereo Control Switch Assembly
        • Active Select Shift Control Paddle Assembly
      • Reassemble
        • Active Select Shift Control Paddle Assembly
        • Horn Bar Stereo Control Switch Assembly
        • Rear Cover
      • Reinstall
    • 3.2 Steering Column Covers
      • Remove
      • Reinstall
    • 3.3 Ignition Barrel and Lock Cylinder
      • Remove
      • Reinstall
    • 3.4 Ignition Switch
      • Remove
      • Test
      • Reinstall
    • 3.5 Steering Column Assembly
      • Remove
      • Inspect
      • Disassemble
        • Non-serviced Components
        • Clock Spring Assembly
        • Tilt/ Reach Handle
      • Reinstall
    • 3.6 Power Steering Fluid Level Check
      • V6 Engine
      • GEN III V8 Engine
    • 3.7 Drive Belt Adjustment
    • 3.8 Tie-rod Socket
      • Remove
      • Reinstall
    • 3.9 Steering Gear Boot
      • Remove
      • Reinstall
    • 3.10 Power Steering Gear Assembly
      • Remove
      • Disassemble
        • Clean and Inspect
      • Reassemble
      • Reinstall
    • 3.11 Power Steering Fluid Reservoir
      • Remove
        • V6 Engine
        • GEN III V8 Engine
      • Reinstall
        • V6 and GEN III V8 Engine
    • 3.12 Power Steering Pump
      • Remove
        • V6 Engine
        • GEN III V8 Engine
      • Disassemble
      • Clean and Inspect
      • Reassemble
      • Reinstall
        • V6 Engine
        • GEN III V8 Engine
    • 3.13 Power Steering Pump Pulley
      • Remove
        • Method 1
        • Method 2
      • Reinstall
        • Method 1
        • Method 2
    • 3.14 Hydraulic System Bleeding and Refilling
      • Procedure
  • 4 Power Steering Hoses, Pipes and Fluid Cooler
    • 4.1 Power Steering Lines and Hoses Layout
      • Arrangement
        • V6 Engine
        • GEN III V8 Engine
      • Remove
      • Inspect
      • Reinstall
    • 4.2 Power Steering Fluid Cooler
      • Arrangement
      • Remove
      • Reinstall
  • 5 Specifications
  • 6 Torque Wrench Specifications
  • 7 Special Tools