holden.wiki

• MODEL SELECTION INDEX
• TF RODEO
• SECTION 6A - ENGINE MECHANICAL (C22NE MODELS)
  • GENERAL DESCRIPTION
    • ENGINE PICTORIAL
      • FRONT VIEW
      • INLET SIDE VIEW
      • REAR VIEW
      • EXHAUST SIDE VIEW
      • TOP VIEW
  • MAIN DATA AND SPECIFICATIONS
    • ENGINE SPECIFICATION MATRIX FOR AUSTRALIA
    • CRANKCASE VENTILATION SYSTEM
    • ENGINE ASSEMBLY & ACCESSORIES
  • OPERATIONS ON ENGINE AGGREGATES
    • ENGINE MOUNTS (ENGINE WITHOUT TRANSMISSION)
    • TOOTHED BELT AND TIMING CHECK
    • TOOTHED BELT TENSION, ADJUST (ENGINES WITH TOOTHED BELT TENSION ROLLER)
    • TOOTHED BELT, REPLACE (ENGINE WITH TOOTHED BELT TENSION ROLLER)
  • OPERATIONS ON INSTALLED ENGINE
    • SEALING OPERATIONS
      • GASKET, EXHAUST MANIFOLD, CYLINDER HEAD
      • GASKET, INTAKE MANIFOLD, CYLINDER HEAD
      • SEAL RING, CAMSHAFT HOUSING, TIMING SIDE
      • SEAL RING, THERMOSTAT HOUSING, CYLINDER HEAD
      • SEAL RING - FRONT CAMSHAFT HOUSING, REPLACE
    • TOOTHED BELT REAR COVER (ENGINE WITH TOOTHED BELT TENSION ROLLER)
    • TOOTHED BELT TENSION ROLLER
  • COMPONENT PARTS
    • CYLINDER HEAD
    • HYDRAULIC VALVE LIFTER
  • OPERATIONS ON CYLINDER HEAD AND CAMSHAFT HOUSING
    • CAMSHAFT
    • CAMSHAFT HOUSING, REMOVAL AND INSTALLATION
    • CYLINDER HEAD
    • HYDRAULIC VALVE LIFTERS, REPLACE
    • CAMSHAFT HOUSING, REPLACE
    • CAMSHAFT HOUSING, CHECK FOR PLANE SURFACE
    • CYLINDER HEAD, REMOVAL AND INSTALLATION
    • CYLINDER HEAD, DISASSEMBLE AND ASSEMBLE
    • VALVE, GRIND
    • VALVE SEATING, MILL
    • CYLINDER HEAD, OVERHAUL
    • VALVE, GRIND
    • FLYWHEEL
    • STARTER RING GEAR (MANUAL TRANSMISSION)
    • SEAL RING, CRANKSHAFT (OIL PUMP HOUSING)
    • SEAL RING, CRANKSHAFT REAR
    • GASKET, OIL PAN
  • OPERATIONS ON CRANKSHAFT
    • CON-ROD BEARING
    • PISTON WITH CON-ROD
    • CON-ROD
    • PISTON RINGS
  • OPERATIONS ON REMOVED ENGINE
    • CRANKSHAFT
    • BEARING FREE PLAY MEASUREMENT
      • 1.PLASTIGAGE METHOD
      • 2.MICROMETER AND GAUGE METHOD.
    • BYPASS VALVE
    • OIL FILTER
    • OIL PUMP
    • OIL PUMP SAFETY VALVE
    • OIL PUMP (OVERHAUL)
  • OPERATIONS ON OIL CIRCUIT
    • CYLINDER HEAD SAFETY VALVE
  • OPERATIONS ON COOLING SYSTEM
    • COOLING SYSTEM, CHECK FOR LEAKS
    • COOLING SYSTEM, FILL UP AND BLEED
    • REFILL COOLANT
    • IGNITION TIMING, CHECK
  • ENGINE EXTERNAL PARTS
    • RADIATOR
    • THERMOSTAT
    • WATER PUMP
    • COATING SEALING SURFACES WITH SILICONE GREASE
    • ALTERNATOR
    • STARTER
    • V-BELT TENSION OF ALTERNATOR
    • V-BELT TENSION OF POWER STEERING PUMP
  • FUEL INJECTION SYSTEM
    • MAP SENSOR
    • PRESSURE REGULATOR
    • ECM (ENGINE CONTROL MODULE)
    • ECT
    • IDLE AIR CONTROL (IAC) VALVE
    • IGNITION COIL
    • CRANK POSITION SENSOR
    • FUEL INJECTOR
    • KNOCK SENSOR
    • OXYGEN SENSOR (IF APPLICABLE)
    • THROTTLE VALVE POSITION SENSOR
    • ACCELERATOR PEDAL AND CABLE
    • AIR CLEANER FILTER
    • SPARK PLUG THREAD
  • TECHNICAL DATA
    • SOHC GASOLINE ENGINE C22NE
    • OIL PUMP
    • COOLING SYSTEM
    • IDLE SPEEDS, CO CONTENT, IGNITION ADJUSTMENT
    • CYLINDER HEAD
    • CAMSHAFT
    • CRANKSHAFT, CYLINDER BLOCK
    • RECOMMENDED TORQUE VALUES
  • SPECIAL SERVICE TOOLS